Parts List

Rooster · May 27, 2003, 19:28

Since nearly everyone is out of parts kits, I would like to try to put together a rifle from available parts. Can anyone give me a parts list for the FAL? This will be my first build and my buddy is helping me.

Rooster · May 27, 2003, 19:29

For a Metric FAL

DAN-PA · May 27, 2003, 19:38

Do a search for "metric Parts" "Jen" in the Marketplace. She has parts and a very nice diagram.

pointman762 · May 27, 2003, 21:03

Or, Tapco is an example of one vendor that has complete Imbel and/or G1 lowers. DSArms has complete Stg58 uppers. Now all you need are the ejector block parts (mag catch, bolt hold open, mag catch spring, mag catch/bho retaining screw), bolt and carrier. Probably run you in the neighborhood of $200-ish dollars for what amounts to a complete Stg58

I'm sure most of the board sponsors and regular vendors will have similar upper/lower bundles floating around out there. And be sure to check the Marketplace forum as well.

Doing it piecemeal will eventually become necessary, I'm afraid.

But until it's "necessary" doing so will nickle & dime you to death....

At least that's where I would be looking

Shrike · June 03, 2003, 22:06

Rooster, call my cell phone or send me an email,
later bro,
Mike

Mosin Guy · June 04, 2003, 11:34

http://www.fnfal.com/falfiles/images/chart2.gif

May 27, 2003, 19:28	#1
Rooster Banned (Temp) FALaholic #: 9328 Join Date: Feb 2003 Location: US Posts: 4,868	Parts List Since nearly everyone is out of parts kits, I would like to try to put together a rifle from available parts. Can anyone give me a parts list for the FAL? This will be my first build and my buddy is helping me.

May 27, 2003, 21:03	#4
pointman762 Registered FALaholic #: 7827 Join Date: Oct 2002 Location: Indiana Posts: 483	Or, Tapco is an example of one vendor that has complete Imbel and/or G1 lowers. DSArms has complete Stg58 uppers. Now all you need are the ejector block parts (mag catch, bolt hold open, mag catch spring, mag catch/bho retaining screw), bolt and carrier. Probably run you in the neighborhood of $200-ish dollars for what amounts to a complete Stg58 I'm sure most of the board sponsors and regular vendors will have similar upper/lower bundles floating around out there. And be sure to check the Marketplace forum as well. Doing it piecemeal will eventually become necessary, I'm afraid. But until it's "necessary" doing so will nickle & dime you to death.... At least that's where I would be looking __________________ "Oh bother" Said Pooh, as the tripwire clicked. "There are two things that are infinite; Human stupidity and the universe... and I'm not sure about the universe." - Albert Einstein

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

May 27, 2003, 19:29	#2
Rooster Banned (Temp) FALaholic #: 9328 Join Date: Feb 2003 Location: US Posts: 4,868	For a Metric FAL

May 27, 2003, 19:38	#3
DAN-PA Registered FALaholic #: 7152 Join Date: Aug 2002 Location: Danville, PA Posts: 232	Do a search for "metric Parts" "Jen" in the Marketplace. She has parts and a very nice diagram.

June 03, 2003, 22:06	#5
Shrike Registered FALaholic #: 4611 Join Date: Oct 2001 Location: Jacksonville, FL Posts: 1,174	Rooster, call my cell phone or send me an email, later bro, Mike

June 04, 2003, 11:34	#6
Mosin Guy Registered FALaholic #: 46 Join Date: Jul 2000 Location: Texas Posts: 3,652	http://www.fnfal.com/falfiles/images/chart2.gif