magazine fit question

henry37 · July 07, 2012, 15:40

hi guys, have a inch kit that is finally put together. to complete the project i purchased a used (yes i know) century receiver. i got it from the market place. the seller assured me that there were no issues with the receiver and that it was inch cut, it came off of a running gun. i took it out to the range. at the time i only had metric mags. i noted a lot of front to back movement but mag still locked in. every time i shot the mag popped out of the back at the mag release. if i wedged a .22 shell between the mag release lever and receiver the gun ran flawlessly. i since bought 2 inch mags. both fit and lock in but really tight. i have issues with the shells getting pick up upon cycling the action. i think it is the mags but not sure. have any of you guys ran into this? is there a fix that can be done? is the receiver really inch cut or metric? am i stuck getting a new receiver?
thanks again, Henry.
__________________
henry37

fnogger · July 07, 2012, 19:57

The metric mags are a "mostly works but sometimes doesn't" thing in an inch cut gun. You may get lucky if you try a few different metric mags.

Or, buy some inch ones. More expensive than metric, but metric prices have been going up so they are getting closer. Once you have your inch ones, sell the metric ones to cover most of the cost (unless you have a metric cut gun as well).

henry37 · July 09, 2012, 22:44

thanks for the info.. i have a friend selling me two inch mags. i already have the two. i will try the two that i am going to pick up tomorrow for fit/function. i do have some metric mags. i can try some of the other metrics on this reciever as well. thanks again, henry.

July 07, 2012, 15:40	#1
henry37 Registered FALaholic #: 62582 Join Date: Jan 2011 Location: idaho Posts: 57	magazine fit question hi guys, have a inch kit that is finally put together. to complete the project i purchased a used (yes i know) century receiver. i got it from the market place. the seller assured me that there were no issues with the receiver and that it was inch cut, it came off of a running gun. i took it out to the range. at the time i only had metric mags. i noted a lot of front to back movement but mag still locked in. every time i shot the mag popped out of the back at the mag release. if i wedged a .22 shell between the mag release lever and receiver the gun ran flawlessly. i since bought 2 inch mags. both fit and lock in but really tight. i have issues with the shells getting pick up upon cycling the action. i think it is the mags but not sure. have any of you guys ran into this? is there a fix that can be done? is the receiver really inch cut or metric? am i stuck getting a new receiver? thanks again, Henry. __________________ henry37 __________________ henry37

July 09, 2012, 22:44	#3
henry37 Registered FALaholic #: 62582 Join Date: Jan 2011 Location: idaho Posts: 57	thanks for the info.. i have a friend selling me two inch mags. i already have the two. i will try the two that i am going to pick up tomorrow for fit/function. i do have some metric mags. i can try some of the other metrics on this reciever as well. thanks again, henry. __________________ henry37

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

July 07, 2012, 19:57	#2
fnogger Registered FALaholic #: 51053 Join Date: Dec 2009 Location: places Posts: 774	The metric mags are a "mostly works but sometimes doesn't" thing in an inch cut gun. You may get lucky if you try a few different metric mags. Or, buy some inch ones. More expensive than metric, but metric prices have been going up so they are getting closer. Once you have your inch ones, sell the metric ones to cover most of the cost (unless you have a metric cut gun as well).