Blueprints

**machanic** · July 02, 2011, 17:34

Looking for a set of blueprints for a FAL upper receiver!!! You got to be kidding! Nobody has had a silly idea of machining a Fal receiver!! machanic

**aezcur** · July 03, 2011, 00:34

I think this is what you are looking for?

http://www.falfiles.com/forums/showt...threadid=67082

**machanic** · July 03, 2011, 07:01

Thank you very much

!!!! Been looking for this with no success. machanic

mountainman · July 03, 2011, 08:33

YOu still need a nother recvr besides you to verify all those numbers.

**4markk** · July 03, 2011, 12:43

Here's a couple posts where someone on here nearly a decade ago milled a receiver from a Century casting.

He has some good insights.

http://www.falfiles.com/forums/showt...threadid=54362
http://www.falfiles.com/forums/showt...threadid=56710

Good Luck !!!!!!!!!!!!!!!!

**machanic** · July 03, 2011, 20:36

I baught one of the torch cut receivers to help with some dimensions, but obviously not all

Needed some basic dimensions just to tack weld it together to study for tooling and jigs. Thanks for all the links to info, very helpful! machanic

July 02, 2011, 17:34	#1
machanic Member Contributor FALaholic #: 63516 Join Date: May 2011 Location: R.I. Posts: 234	Blueprints Looking for a set of blueprints for a FAL upper receiver!!! You got to be kidding! Nobody has had a silly idea of machining a Fal receiver!! machanic Last edited by machanic; July 02, 2011 at 20:02.

July 03, 2011, 00:34	#2
aezcur El Argentino Gold Contributor FALaholic #: 49232 Join Date: Sep 2009 Location: WA, USA Posts: 2,432	I think this is what you are looking for? http://www.falfiles.com/forums/showt...threadid=67082 __________________ AEZCUR Mi Buenos Aires querido........

July 03, 2011, 12:43	#5
4markk Military Observer Silver Contributor FALaholic #: 31134 Join Date: Aug 2007 Location: Northern Virginia Posts: 2,280	Here's a couple posts where someone on here nearly a decade ago milled a receiver from a Century casting. He has some good insights. http://www.falfiles.com/forums/showt...threadid=54362 http://www.falfiles.com/forums/showt...threadid=56710 Good Luck !!!!!!!!!!!!!!!! __________________ ` ` The difference between the possible and the impossible is only in the degree of a man's will. Chinese Proverb “The worst thing about growing old is that other men stop seeing you as dangerous.” Act Of Valor

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

July 03, 2011, 07:01	#3
machanic Member Contributor FALaholic #: 63516 Join Date: May 2011 Location: R.I. Posts: 234	Thank you very much !!!! Been looking for this with no success. machanic

July 03, 2011, 08:33	#4
mountainman Registered FALaholic #: 14702 Join Date: Jun 2004 Location: Deltona FL Posts: 3,192	YOu still need a nother recvr besides you to verify all those numbers.

July 03, 2011, 20:36	#6
machanic Member Contributor FALaholic #: 63516 Join Date: May 2011 Location: R.I. Posts: 234	I baught one of the torch cut receivers to help with some dimensions, but obviously not all Needed some basic dimensions just to tack weld it together to study for tooling and jigs. Thanks for all the links to info, very helpful! machanic