WTS USGI M1A bedlinered stock (pics) *SOLD*

tiblow · April 04, 2008, 16:04

I have for sale a USGI M1A fiberglass stock that I had sprayed with custom bed liner by Line-X. The stock was a very nice form with nice crisp raised grip areas on the PG and forward on the stock at the hand holds. It’s a GI fiberglass that had for some reason discolored from its normal brown tone such that it was a candidate for this special treatment otherwise in perfect shape. I wanted to make essentially a stock like the SOCOM rifle but discovered a friend had an original one he wasn’t using any more and got a real SOCOM stock for a trade. Now I don’t need this one.

The stock was professionally masked/taped by the technician at the butt, the magwell and along the top edge where the recv would sit inside the stock. The it was shot with a thin but complete coating of black Line-X and the areas that were not shot with the Line-X were pre-sprayed by me with two light coats of flat black alumahide II.

It came out nice but I really wanted the real thing. This one has a nice rough feel to it (he fogged it with a nice mist) but not enough to rub your cheek raw. It’s a nice texture all around. No other hardware comes with it but the front sling swivel that I have not put back on yet (taped on in the pics). I was going to use the black rubber butt pad on it instead of a standard M1A pad anyway.

Line-X charged me $45 to do it and so I’m asking just for that + shipping.
Thanks

See pics below......

robmac · April 04, 2008, 16:16

Left side

robmac · April 04, 2008, 16:21

Bottom

robmac · April 04, 2008, 16:22

Butt

astroman2057 · April 04, 2008, 17:08

I'LL TAKE IT!!!PM sent requesting preferred payment info, address, etc.
Thanks!!
Dennis

tiblow · April 04, 2008, 18:08

*SOLD*

Thanks

April 04, 2008, 16:04	#1
tiblow Registered FALaholic #: 12893 Join Date: Dec 2003 Location: middle earth Posts: 1,097	WTS USGI M1A bedlinered stock (pics) SOLD I have for sale a USGI M1A fiberglass stock that I had sprayed with custom bed liner by Line-X. The stock was a very nice form with nice crisp raised grip areas on the PG and forward on the stock at the hand holds. It’s a GI fiberglass that had for some reason discolored from its normal brown tone such that it was a candidate for this special treatment otherwise in perfect shape. I wanted to make essentially a stock like the SOCOM rifle but discovered a friend had an original one he wasn’t using any more and got a real SOCOM stock for a trade. Now I don’t need this one. The stock was professionally masked/taped by the technician at the butt, the magwell and along the top edge where the recv would sit inside the stock. The it was shot with a thin but complete coating of black Line-X and the areas that were not shot with the Line-X were pre-sprayed by me with two light coats of flat black alumahide II. It came out nice but I really wanted the real thing. This one has a nice rough feel to it (he fogged it with a nice mist) but not enough to rub your cheek raw. It’s a nice texture all around. No other hardware comes with it but the front sling swivel that I have not put back on yet (taped on in the pics). I was going to use the black rubber butt pad on it instead of a standard M1A pad anyway. Line-X charged me $45 to do it and so I’m asking just for that + shipping. Thanks See pics below...... Last edited by tiblow; April 04, 2008 at 18:07.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

April 04, 2008, 17:08	#5
astroman2057 Registered FALaholic #: 9295 Join Date: Feb 2003 Location: Sterling Alaska Posts: 333	I'LL TAKE IT!!!PM sent requesting preferred payment info, address, etc. Thanks!! Dennis

April 04, 2008, 18:08	#6
tiblow Registered FALaholic #: 12893 Join Date: Dec 2003 Location: middle earth Posts: 1,097	SOLD Thanks