bolt won't close

Chipmunk · March 03, 2001, 19:22

It seems that I have a slight bind in the reciever,
while closing bolt slowly,it stops about 3/4 of the
way closed,a RKI suggested that since it's a Hesse
it is probably out of spec (reciever).When it stops,
all I have to do to get it to close completely, is tap
it lightly with my fingertip.Question is could I use
copper sulfate to give me an indication of where it is
binding and then use valve lapping compund to relieve
the bind?Thanks in advance for y'alls replies.
Chipmunk

[ July 22, 2001: Message edited by: gary.jeter ]

Rich@CGW · March 03, 2001, 21:40

Most likely, it is hanging up on the HAMMER spur as it slowly rides over it..This is common when you are just monkeying around with it and letting the bolt close slowly. Most ALL Fals will do this. if it hangs up when you charge the weopon like you mean it, then you may have another problem.

Aifwikir · March 03, 2001, 22:07

I agree with Rich! The hammer is holding it open at that point. If it hangs when closing the bolt from the "Bolt Hold Open Device" or from the full charge position, then you have a different problem.

Take care
Aif

------------------
I don't SUFFER from insanity,,,,
I ENJOY IT!!

Rich@CGW · March 03, 2001, 22:21

Just a NOTE; incase you had some dim light go off in your head,

thinking you can just remove some of that hammer spur material that may bug ya so much..DONT, It is needed to set the hammer when cycling back. it will smooth out on it`s own.. 2-300 rounds usually..

Chipmunk · March 04, 2001, 00:04

Thank you Gentlemenfor your prompt
& knowledgeablereplies,I hadn't thought
about the hammer.I'll run some morethrough
it later on today,if the snow don't blow.Once
again thanks!
Chipmunk

------------------
"If you love wealth better than liberty, the tranquillity of servitude better than the animating
contest of freedom, go home from us in peace. We ask not your counsels or arms. Crouch down and lick the hands
which feed you. May your chains set lightly upon you and may posterity forget that ye were our countrymen."
--Samuel Adams --

March 03, 2001, 19:22	#1
Chipmunk Registered FALaholic #: 213 Join Date: Jul 2000 Location: Richmond,Va. CSA Posts: 693	bolt won't close It seems that I have a slight bind in the reciever, while closing bolt slowly,it stops about 3/4 of the way closed,a RKI suggested that since it's a Hesse it is probably out of spec (reciever).When it stops, all I have to do to get it to close completely, is tap it lightly with my fingertip.Question is could I use copper sulfate to give me an indication of where it is binding and then use valve lapping compund to relieve the bind?Thanks in advance for y'alls replies. Chipmunk [ July 22, 2001: Message edited by: gary.jeter ] __________________ You don't stop laughing because you grow old; You grow old because you stopped laughing.

March 03, 2001, 21:40	#2
Rich@CGW Registered FALaholic #: 167 Join Date: Jul 2000 Location: Gardnerville , NV. Near Lake Tahoe Posts: 1,826	Most likely, it is hanging up on the HAMMER spur as it slowly rides over it..This is common when you are just monkeying around with it and letting the bolt close slowly. Most ALL Fals will do this. if it hangs up when you charge the weopon like you mean it, then you may have another problem. __________________ Will work for cash & pine nuts

March 03, 2001, 22:07	#3
Aifwikir Registered FALaholic #: 2187 Join Date: Jan 2001 Location: Magazine, Arkansas Posts: 3,061	I agree with Rich! The hammer is holding it open at that point. If it hangs when closing the bolt from the "Bolt Hold Open Device" or from the full charge position, then you have a different problem. Take care Aif ------------------ I don't SUFFER from insanity,,,, I ENJOY IT!! __________________ Cosmo the Lene,,, Smeller of old grease! http://i105.photobucket.com/albums/m...ber3575new.jpg

March 03, 2001, 22:21	#4
Rich@CGW Registered FALaholic #: 167 Join Date: Jul 2000 Location: Gardnerville , NV. Near Lake Tahoe Posts: 1,826	Just a NOTE; incase you had some dim light go off in your head, thinking you can just remove some of that hammer spur material that may bug ya so much..DONT, It is needed to set the hammer when cycling back. it will smooth out on it`s own.. 2-300 rounds usually.. __________________ Will work for cash & pine nuts

March 04, 2001, 00:04	#5
Chipmunk Registered FALaholic #: 213 Join Date: Jul 2000 Location: Richmond,Va. CSA Posts: 693	Thank you Gentlemenfor your prompt & knowledgeablereplies,I hadn't thought about the hammer.I'll run some morethrough it later on today,if the snow don't blow.Once again thanks! Chipmunk ------------------ "If you love wealth better than liberty, the tranquillity of servitude better than the animating contest of freedom, go home from us in peace. We ask not your counsels or arms. Crouch down and lick the hands which feed you. May your chains set lightly upon you and may posterity forget that ye were our countrymen." --Samuel Adams -- __________________ You don't stop laughing because you grow old; You grow old because you stopped laughing.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode