Thread of the magazine release pivot screw?

TooTech · January 06, 2001, 22:06

I can't get the mag release pivot screw to bottom out on my Imbel receiver. The screw is out of an R1 kit. Before it can bottom out the screw becomes REAL hard to turn, leaving about a 1/16" of the head about the receiver surface. There is plenty of depth in the screw head inlet (tested by reversing and inserting the screw head), and the hole on the other side of the receiver is clear (tested by pushing screw end in from other side).

The leading threads on the screw are shiny, and I have a feeling I need to chase out the threads in the ejector block. Or am I missing something?

Otherwise, what tap do I need to clean out the ejector block threads?

Thanks!

derek huffman, azexarms · January 06, 2001, 23:27

10/32. drill out with the proper size drill, perhaps a bit of mis-fit on the ejector block, a small problem. D.

TooTech · January 07, 2001, 10:42

Thanks Derek, worked like a champ!

I own exactly ONE tap, and it just happened to be a 10/32!

How's that for serendipity?

derek huffman, azexarms · January 07, 2001, 15:01

Sometimes the planets align just for us...Fal brother!

D.

**W.E.G.** · September 09, 2001, 14:20

I ran into this exact same problem with a recently-manufactured IMBEL type 3 metric receiver and a Chilean IMBEL parts kit.

Rather than drilling on the receiver, I think I'll just file the leading portion of the threads on the pin. Not like you need a lot of thread-engagement for securing this screw.

(The truth be told I DID WECSOG the screw head, as at first I thought the screw head was slightly to large to go into the countersunk recess. Now I have a very "sleek" screw-head for this part.)

January 06, 2001, 22:06	#1
TooTech Registered FALaholic #: 465 Join Date: Jul 2000 Location: St. Paul, MN Posts: 569	Thread of the magazine release pivot screw? I can't get the mag release pivot screw to bottom out on my Imbel receiver. The screw is out of an R1 kit. Before it can bottom out the screw becomes REAL hard to turn, leaving about a 1/16" of the head about the receiver surface. There is plenty of depth in the screw head inlet (tested by reversing and inserting the screw head), and the hole on the other side of the receiver is clear (tested by pushing screw end in from other side). The leading threads on the screw are shiny, and I have a feeling I need to chase out the threads in the ejector block. Or am I missing something? Otherwise, what tap do I need to clean out the ejector block threads? Thanks!

September 09, 2001, 14:20	#5
W.E.G. Administrator Silver Contributor FALaholic #: 1211 Join Date: Oct 2000 Location: Virginia Posts: 31,056	I ran into this exact same problem with a recently-manufactured IMBEL type 3 metric receiver and a Chilean IMBEL parts kit. Rather than drilling on the receiver, I think I'll just file the leading portion of the threads on the pin. Not like you need a lot of thread-engagement for securing this screw. (The truth be told I DID WECSOG the screw head, as at first I thought the screw head was slightly to large to go into the countersunk recess. Now I have a very "sleek" screw-head for this part.) __________________ . . . Ask me about the Mason-Dixon FAL Collectors Association.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

January 06, 2001, 23:27	#2
derek huffman, azexarms Perm Banned FALaholic #: 206 Join Date: Jul 2000 Location: Mesa, AZ USA Posts: 1,392	10/32. drill out with the proper size drill, perhaps a bit of mis-fit on the ejector block, a small problem. D.

January 07, 2001, 10:42	#3
TooTech Registered FALaholic #: 465 Join Date: Jul 2000 Location: St. Paul, MN Posts: 569	Thanks Derek, worked like a champ! I own exactly ONE tap, and it just happened to be a 10/32! How's that for serendipity?

January 07, 2001, 15:01	#4
derek huffman, azexarms Perm Banned FALaholic #: 206 Join Date: Jul 2000 Location: Mesa, AZ USA Posts: 1,392	Sometimes the planets align just for us...Fal brother! D.