Assembly/disassembly of Israeli bolt

JoeLad · June 10, 2004, 15:05

I bought an Israeli bolt and one piece extractor for the Izzy clone I'm planning.
The extractor has a weird spring that look like a check mark.

It looks as if the upright part of the check (spring) fits into a hole in the bottom of the extractor. Then the curved part of the check fits into a groove cut into the side of the extrator. Am I correct so far?
The spring is very stiff. If I do get it together, how do I take it apart?
It's unlike any other FAL extractor combo I've ever seen.
Those whacky Israelis!

JoeLad

Derby FALs · June 10, 2004, 22:57

I think you pry it back, then up and out. Been a while since I did one.

JoeLad · July 06, 2007, 22:32

WTF? How is it this came up 3 years later?

Windustsearch · July 07, 2007, 10:29

Screwdriver, the one-piece extractor removal tool. The straight part of the spring goes into the bottom of the extractor, the curved part goes up against the bolt.

gunsmith_tony · July 07, 2007, 11:46

Quote:

Originally posted by Windustsearch
Screwdriver, the one-piece extractor removal tool. The straight part of the spring goes into the bottom of the extractor, the curved part goes up against the bolt.

And chances are you already have the installation tool...your thumb.

**W.E.G.** · July 07, 2007, 11:54

Quote:

Originally posted by JoeLad
WTF? How is it this came up 3 years later?

I wonder...

http://www.falfiles.com/forums/showt...26#post1969526

JoeLad · September 01, 2012, 21:11

Back again from the great beyond...

TerryN · September 02, 2012, 01:45

Let it die. Finally.

**johnny.308** · September 03, 2012, 10:07

Quote:

Originally Posted by TerryN

Let it die. Finally.

Actually it is very timely as most of the Sarco Argy kits came with one piece extractors in case those of you who bought them don't know. There will be blood.

June 10, 2004, 15:05	#1
JoeLad Registered FALaholic #: 3353 Join Date: Jun 2001 Location: SE PA Posts: 3,241	Assembly/disassembly of Israeli bolt I bought an Israeli bolt and one piece extractor for the Izzy clone I'm planning. The extractor has a weird spring that look like a check mark. It looks as if the upright part of the check (spring) fits into a hole in the bottom of the extractor. Then the curved part of the check fits into a groove cut into the side of the extrator. Am I correct so far? The spring is very stiff. If I do get it together, how do I take it apart? It's unlike any other FAL extractor combo I've ever seen. Those whacky Israelis! JoeLad

June 10, 2004, 22:57	#2
Derby FALs Supreme Leader FALaholic #: 2361 Join Date: Jan 2001 Location: Louisville, Kentucky Posts: 2,610	I think you pry it back, then up and out. Been a while since I did one. __________________ “Rightful liberty is unobstructed action according to our will within limits drawn around us by the equal rights of others. I do not add "within the limits of the law" because law is often but the tyrant's will, and always so when it violates the rights of the individual.” - Thomas Jefferson Salami, salami, baloney... :bow: http://www.derbyfals.com/home.htm

July 07, 2007, 10:29	#4
Windustsearch Registered FALaholic #: 10219 Join Date: Apr 2003 Location: Seattle,Wa Posts: 5,696	Screwdriver, the one-piece extractor removal tool. The straight part of the spring goes into the bottom of the extractor, the curved part goes up against the bolt. Last edited by Windustsearch; July 07, 2007 at 10:37.

September 02, 2012, 01:45	#8
TerryN Registered FALaholic #: 55 Join Date: Jul 2000 Location: Yuma, AZ Posts: 1,564	Let it die. Finally. __________________ Sic Semper Tyrannis! Molon Labe!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

July 06, 2007, 22:32	#3
JoeLad Registered FALaholic #: 3353 Join Date: Jun 2001 Location: SE PA Posts: 3,241	WTF? How is it this came up 3 years later?

September 01, 2012, 21:11	#7
JoeLad Registered FALaholic #: 3353 Join Date: Jun 2001 Location: SE PA Posts: 3,241	Back again from the great beyond...