The FAL Files  

Go Back   The FAL Files > Weapons Discussion > General Firearms Discussion


Thread Tools Display Modes
Old January 14, 2013, 16:36   #1
FALaholic #: 67991
Join Date: Nov 2012
Location: PA
Posts: 93
Guy uses 3D printer to make his own mags

I read about this a while ago, apparently this is becoming more and more easy to do. They even make stripped lowers with the 3D printer. If you browse the site you will see a video of them testing the printed lower to failure. It's pretty funny, the guy squezes off a few rounds and it completely falls apart. But, this technology is pretty cool.

here's the site that has the templates:
USMC Infantry
Semper Fi

Last edited by macmac360; January 14, 2013 at 16:42.
macmac360 is offline   Reply With Quote
Old January 14, 2013, 17:02   #2
starbuck's Avatar
FALaholic #: 26466
Join Date: Feb 2007
Location: OHIO
Posts: 871
I like this guy but they'll screw him like a hacker. 95% of congress has no idea what hes doing. What that means is the 5% that does can sneak through some legislation where its illegal to P2P weapons.
In a closed society where everybody's guilty, the only crime is getting caught.
starbuck is offline   Reply With Quote
Old January 14, 2013, 18:46   #3
Average White Devil
Bronze Contributor
Pluribus's Avatar
FALaholic #: 5600
Join Date: Feb 2002
Location: Wichita, America
Posts: 4,128
It's just the lower and the dimwitocrat said it's a GUN. Yeah, I know the lower is the Gun.

You know, if you kick a dog enough, eventually they'll stop coming around.

Were it not for ignorance, thus we would remain.

Never hate your enemy, it only clouds your judgement.
Pluribus is offline   Reply With Quote
Old January 14, 2013, 18:53   #4
FALaholic #: 67991
Join Date: Nov 2012
Location: PA
Posts: 93
back to the drawing board LOL

need stronger plastic LOL
USMC Infantry
Semper Fi
macmac360 is offline   Reply With Quote
Old January 14, 2013, 20:14   #5
Curio & Relic
Bronze Contributor
FALaholic #: 365
Join Date: Jul 2000
Location: Commonwealth of Virginia, CSA
Posts: 2,108
I had seen a post somewhere (ARFCOM or Weaponeer) where someone was going to attempt to make a functioning lower out of paper bonded with epoxy. As I recall, some type of CAD/CAM stencil cutter would print out longitudinal cross-sections of the receiver in paper. These cross sections would then be stacked in order using pins through alignment holes. The the stack was then clamped between two plates, and the whole deal immersed in some type of thin polymer solution that would impregnate the paper layers over several days. The frame would then be removed from the solution and allowed to cure. After curing, final touch-up and machining.

Never heard how that experiment went...


P.S. The same poster had planned to machine an AR lower out of finely layered cabinet-grade plywood, using metal liners for the for screw holes, and the holes for the TG pins.

It's sh*t like this, that makes America great.
"Buy all the beans, bullets, and band-aids you can afford boys. It's no longer a question of "IF", it's now only a question of "WHEN"."
JohnnyMac is offline   Reply With Quote
Old January 14, 2013, 20:26   #6
FALaholic #: 22871
Join Date: Dec 2006
Location: Texas
Posts: 1,193
I downloaded the cad drawings for the mag and lower a while back. The six shot failure was remedied shortly after failing by reinforcing the rear area where the recoil tube screws in the receiver.

I also saw one demo where the gun went through several full mags without issue. The 3d printers are now down in the $500 dollar range.
mutter is online now   Reply With Quote
Old January 14, 2013, 20:31   #7
FALaholic #: 10331
Join Date: Apr 2003
Location: west central Florida
Posts: 2,337
but it is a good start can you say liberator pistol/ rifle any one
"Our conduct defines us." What every officer should live by.
It's the tool behind the tool that makes the difference. ~ Chet
Jailguard is offline   Reply With Quote
Old January 14, 2013, 21:06   #8
Silver Contributor
FALaholic #: 50609
Join Date: Nov 2009
Location: The Peoples' Republic of Boulder, Colorado
Posts: 11,698
Why not a cardboard lower?

There is no theory of evolution, just a list of creatures Chuck Norris allows to live.
def90 is online now   Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

All times are GMT -5. The time now is 16:22.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
©1998-2015 The FAL Files