The FAL Files  

Go Back   The FAL Files > Weapon Specific Forums > The Shotgun Files

Notices

Reply
 
Thread Tools Display Modes
Old March 17, 2013, 03:23   #51
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is picture of the 12ga short brass RMC cases being used in
the 1887 WIN shown above. They are 2 5/8" long cases and we
get 600gr over 1900. He had work done on action to get it to feed
these and 3" roll crimped plastic. Brass loaded about same length
as 3' plastic crimped little long.



Next pic are Lyman slugs cast for thin 12ga wad, used in thickwall
10ga VP100 wads. These Lymans I got are on large size and fit
VP100 fairly well. Makes easy, lighter, superfast load in 10ga.



Next; further idea with Longbow's tube/roundball slug shown above.
Use tube hot glued to ball with screw in the back and use it in
a 10ga VP100 wadcup. These type slugs little more accurate used
in wads as opposed to fullbore.



Next shows picture of a long 585 bullets, about 1600gr in our 585HE
cases. Got the idea from Bret In Minn that could setup 585HE
guns with super long throat and load down to subsonic speeds to
make the 585HE Whisper.....And regular bullet loads would still fire
in the same guns......And at subsonic 1050fps it would have about
4000 ft lbs, about twice what the peashooter whisper cases have.
And my case could get a 2400 gr long bullet to same subsonic speed
for 6000 ft lbs. And one that long would have proportions like the
newer tank cannon, smooth barrel saboted darts, that it could be
possibly be done, using long 2400gr in smooth barrel.
Neat ideas from guys interested in whisper type loads.



Last is picture of FBW in our 585HE with handgrip stock and light
barrel for lightweight carrying. Grip is weighted, gun is 6lbs.
Barrel is 28". I'm not a fan of light barrels. 650gr at 2500 is max of
what I can hold onto shooting from the hip Moderate load
.Little info about my 585 loads, like in the break actions and the
Mossy in post above. I load about 85% max velocities, but to get
85% we only need 2/3 the peak pressure, like 40,000 psi
instead of 65,000...Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old March 29, 2013, 02:29   #52
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
We have a winner it seems. The 12ga sabots using 58cal slugs.



The sample 12ga sabots got here earlier this week. And we got a bunch
of testing already for opening and sealing, and some accuracy testing .440gr
Minie bullet, measuring .575"; with OD of sabot with slug in it of .737" It is
perfect. Going moderate 1800. Petals opened perfect and evenly and they all
stayed on perfect. No petals twisted or torn. Tested in 3" case with slower
powder loads. 80gr of 4759 and 50gr Alliant Steel. Fiocchi case.
Savage 210 rifled barrel, 1 to 35 twist. Cases with slower powders expanded
only a little, and those cases are soft ones.
We have big bunch of the sabots here now.




All petals were opened at about 30 deg to the base when picked up.
With ither powder the bases have no damage, or burn throughs or melting.
Took rifling perfect, so skidding on the rifling. Most of the rifling grip is on the
bottom half of sabot, which is why these and Accutips are best as the bottom
is full size instead of dropping back in size, compared to the top, like many
other sabots. Rifling in the barrel still clean..



The Minies are hollow based and the slug edges did not cut into the inside of the
sabot bases,just a slight impression. We have got good base thickness.
Good Accuracy - In the cold and very windy day, hit milk jugs at 30 yds.
Here is picture inside sabot showing just a slight indent. No need of cards under
slugs, and if you did, the the slugs would set up in sabot and not have the
curve of the slug behind the inside circular rib for best fit...

You got to use right powders. With right slower powders( not fast shotgun),
that start easier and used in larger amounts, you won't tear up the sabots.
It is false economy to use all fast shotgun powders,trying to get twice as many
shots per pound... and tear up sabots, expand cases too much, get poor groups,
miss that deer or whatever. For most of you in 3" cases Alliant Steel is best.

Get with me for sabots -- gunowner at journey.com Ph- 1-989-644-5228
THE undersize blue ones sold elsewhere for 34 bucks a hundred plus postage.
Ours are 33 bucks per 100 postage included, or $20 for 50 postage included,
with a bonus WE WILL send along 10 slugs with 100 order, 5 with 50 order.
to show you what to get and to test with. Slugs can be 440gr or 500gr..Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old March 30, 2013, 18:02   #53
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is picture of a bunch of the sabots with different slugs and bullets.
Back Row- Two roundball load, balls 285gr each-- pointed long 700 gr -- a blunt
solid 700gr-- tungsten slug 1000gr --- jacketed bullet -- 600gr.
2nd row-611 Lyman 530gr Minie- 500gr flat base- Lee 500gr hard--Lee 500gr soft
1st Row- Lyman 440gr old style minie-- Lyman 510 gr new style-- 440gr from Dixie
Gunworks-- 400gr Lee target style. I like 440gr old style and 440 gr Dixie. For sale
on Gunbroker is all sizes and weights.. Or cast your own. Lots of moulds around.
Lee moulds only 20 bucks. Best diameters to use are .574 " to .577" Minies.
If you have ones bigger and they are not hardened you can roll them betweem two
hard surfaces and they will get little smaller. I have some that are .585" 440gr
and work in my 585HE and they can be rolled smaller.



Here are sabots with variety of seals/wads, and the shortest one in picture with
white felt wad just fits in 3" case with 80gr 4759, and still leaves room to roll crimp.
I compress it in hard. Now only faster powder than 4759 I'd use is Alliant Steel in
smaller amounts, 50gr Steel, in 3", and thicker wads and cushions like shown.
To roll crimp over the top edge of sabot we had .220" of case before crimping.
You only have to crimp top edge of sabot real good.




After crimping the slugs are tight and don't move around. The circular rib inside the
sabot holds slugs tight back into the base. Speeds over 2000 fps
will be gotten using 3.5" plastic cases, with our slower powder loads. .
More testing for accuracy yesterday, a warmer, calmer day, with steel sights.
Hit. paper plate at 50 yds.

As said above, best to use right powders. Right slower powders( not fast shotgun),
that get to peak pressure slower, thus can use larger amounts, can get to higher
velocities, and you won't tear up the sabots and won't expand cases as much.

For most of you in 2.75" and 3" cases Alliant Steel is best.
FOR 440GR SLUGS IN SABOT---For 2.75" start at 40gr and go up to about 50.
For 3" start at 45gr go up to about 55. I like 3.5" best as you can load much easier
for speed, still have more cushion wads. Start with 50gr Steel, go up to about 62.
Case brands act different, but using the slower powders minimizes the differences
and keeps us away from surprizing pressure problems.

In 3" plastic,most 4759 I can get in and still have 1/4"cushion is 80gr.... In the 3.5"
I can get in 105 gr with this sabot and get over 2000 fps, In these loads if using
480-500gr cut back 3 gr. These 58cal slugs can be cast or they are at Dixie Gunworks
and 4 guys on Gunbroker got them. Get ones .574" to .577"


Interested in sabots--- gunowner at journey.com Ph- 1-989-644-5228
THE undersize blue ones sold elsewhere for 34 bucks a hundred plus postage.
Ours are 33 bucks per 100 postage included.
Or $20 for 50 postage included..
.Or 150 for $45 postage included----- ALL with a bonus
WE WILL send along 10 slugs with 100 order, 5 with 50 order. 15 with 150 order.
to show you what to get and to test with. Slugs can be 440gr or 500gr......Ed
__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old April 04, 2013, 21:58   #54
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is picture of 45-50yd target, used a scoped NEF Ultra, the sabot load of a 440gr
58cal slug in it at 1800... Measures 2.5" on outside for 3 shots.



Here is pic of almost 2100 of them. More coming. Time to
get them and get loads working.



And A little funnin humor for us big bore nuts..Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old April 07, 2013, 21:59   #55
gus
Registered
 
FALaholic #: 12709
Join Date: Dec 2003
Location: willaimsburg va
Posts: 122
can we ...

go to the hood and hunt suvs now ??? mounting escalate on the wall would be a small bit of work ! i too like small caliber weapons .....
__________________
when a nation turns on it's own and denies it's own founding culture ,this is a sign of the death pangs of a nation --- cz7
gus is offline   Reply With Quote
Old April 09, 2013, 20:00   #56
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Some more info about our sabots and various slug weights......
First and most important is our sabots fitting real tight like the Accutip
Sabots, they will not get the same speed at the same pressures as
the undersize grey and blue ones, But they do leave the barrel
headed straighter and without damage, even with hollowbase 58cal
slugs in them as the pics above show. No cards under slugs in sabots.,
But with good powder seals, using Alliant Steel, and good 1/4" minimum
cushion wads.

The 440gr Minie slug of .575" in the 3" cases is the one I used as a
base loading, to work each way by weight to find what loads of
Alliant Steel work and extract in my NEF. Using 3" soft base cases.
Here is pic of before/after of Fiocchi cases, on right unfired and left
fired, 55gr Steel with 440 gr slug.



For 440gr max of 55gr Steel
For 400gr max of 57gr Steel
For 360gr max of 59gr Steel

For 490gr max of 52gr Steel.
For 510gr max of 49gr Steel
For 540gr max of 47gr Steel.

I tested all these weights for extraction. It is real nice to reach into a
bucket, grap a sabot that fits right, and go to loading and shooting.
Many of you need to get in on the fun.
Here is picture of Fiocchi with sabot, roll crimped. The top of sabot is
perfect for roll crimping...It is setting under crimp tool in drill press.



Earler I showed the 585HE Falling block with pistol grip and the light
barrel. Here it is with Knoxx Compstock buttstock. We added 2 extra
springs inside for relatively hard recoiling gun, as stock originally made
for a REM 870 Pump. Works great and looks nice; will putting one on
the Magtech 585HE singleshot break action and got one in rifle stock
for Ruger 77 in 585HE.



And many guys want wildcats with shoulders, with big neck down, so
in developing the ultimate 700 blaster, here is the 700HSM. Shown next
to Gibbs 650gr ball powder..1000gr at 3800...How about that.
Will be one of only 2 guns I plan on being over 30 lbs, other is 2bore..
Whoppee.....Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old May 06, 2013, 21:26   #57
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
The sabots work in brass cases .First is sabot in a Magtech brass case,
next to 3" plastic.. In shorter brass it would hold about as much powder
as in longer plastic if loaded like in the picture..
Sabots are about .734-735" with slugs in them, and
the Magtech brass with its thin sides still is slightly small OD at the
top compared to plastic, with sabot wedged in.



Next is sabot in RMC case, and sides are full thickness like plastic cases
at the mouth, so don't expand case to hold sabot. We have RMC make case
mouth ID to fit sabot. Sabot being little over fits barrels tight and rifling
impresses into plastic well and gets best spin, and being tight it leaves barrel
straight, with petals opening evenly. Brass case mouths are tight enough that
we push sabot in with a press.Saves trying to crimp heavy RMC case.



Here is picture of a barrel and barrel on a gun from 20 gauge singlshots that
will have the heavy 20ga rifled barrel in picture, mono-blocked into them.




The sabots are not moving very fast and I need money out of them asap, an
emergency bill coming... And seeing as how we're low on slugs to send with
the sabots, in big numbers, and no one has yet to buy out our stash of sabots,
and set up so they can be selling the sabots, we will try selling them
fast in next few weeks . So we will be having a sale on just the sabots, in larger
amounts only. We will send one each of 440gr and 500gr slug so the guys
can see what we have found that works.
Because of the shipping costs and boxes that 2, 3, or 4 bags of sabots fit
in, that have an affordable postage cost to pay,we will sell these in 200,
300, and 400 size orders..So, 200 sabots $47 Shipping included,
300 sabots $65 Shipping included...400 for $83 shipping included.
Now 200 of the other brand X of undersize ones cost $68 plus shipping.
There was dozens of guys the last few years all over the internet that bought
undersize junk, that wanted good sabots, and complained that the ones they
bought elsewhere didn't work......We haven't heard from most of them, So guys
see if you got time, please help us out here..And setup for good shooting...Ed
__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old May 26, 2013, 17:13   #58
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
What causes sabot problems/inaccuracy. Some pictures will help.
First 2 shows a skinny post that pushes on a cushion or sabot
bottom and it can bend or deflect which if that way when exiting
barrel can start sabot or slug crooked.





And more important item that can cause lack of accuracy is if
base of discarding sabot tapers or steps down so that it isn't real
tight as it leaves bore, which can allow it to be cocked.
On the left is our sabot which has base right and other brand
which tapers a bit. Easy to see.



Next is a ball and slug load in 2 of our sabots. A 285gr .575" ball
flattened, put in the bottom and 400gr Minie above, two different
styles of Minies.



Here is couple 16ga discarding sabots I made from the undersize
12ga grey ones. Didn't have to take off much. Much better use
for them. I made them, after Paul in Alaska asked about
where to find 16ga ones, to see what they looked like.
They still use 50cal slug.. Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old June 22, 2013, 15:57   #59
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is 16ga discarding sabots made from grey ones with other 16ga slugs..
20 ga factory sabot on left for comparison.



Here is picture of 12ga wads showing good and bad support to the
bottom of the slug.If in part of the loads the support gets cocked, then
the slug won't be straight on and can account for open groups.



Here are 2 sabots on the right with super heavy tungsten slug. It is 1100gr,
but tungsten costs ten times what lead costs.



Here is a sabot home defense or close range defense load setup using our
sabot. It has five flattened 45cal balls in it. Flattened into a fat disc weighing
145gr each. You'd star crimp it or use card over them and roll crimp. Like
having a bunch of supersize flat buckshot, only super size.



Here is comparison picture of the 58cal slugs used in our 12ga sabots, with the
puny slugs used in many other sabots. And we've moved 5500 of the sabots.
Deer season is coming fast. Maybe time to get loads tested/sighted in is now.



Some more figures. The 24hr Campfire forums is first one, with our 12ga FH thread,
to get over half million thread views.The HighRoad second.
TheFiringLine, third. AccReloading fourth...Ed
__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old July 06, 2013, 00:49   #60
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
We have moved few thousand sabots.More here.
Here is picture of an 8ga wad with tube slug in it, we made.



A pallet load of our 585HE cases has arrived in the US
and will be here in little while. And should be another pallet
of them this fall. Here is picture of our 585
with the solid turned CEB bullets in them.



Here is some helpful, simple math to help figure out the kinetic energy
of your loads, just by having bullet weight and speed.
Just put these multipliers which are used for each speed, on a list
and multiply by the bullet weight in grains. Fast and easy.Ed

Speed..Multiplier
1500------5
1600------5.7
1700------6.42
1800------7.2
1900------8
2000------9
2100------9.8
2200------10.75
2300------11.75
2400------12.8
2500------13.9
2600------15
2700------16.2
2800------17.4
2900------18.7
3000------20
__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old July 18, 2013, 18:35   #61
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is picture of current 58cal slug options that
you can get molds for from Lyman,
Just make sure they are .574" to .577" diameter,
the best size for the 12ga sabots.




A barrel of 585HE cases..Ed



Made by Bertram and I tested them to max loads and cases hardly expanded,
650gr over 3000 fps. The same draws used by him to make high pressure
Cheytac cases, and to finish mine just uses belted header and cases left
straight and trimmed longer.He makes tens of thousands Cheytac steady all
the time now and can make ours steady also when needed.....Ed
__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old July 19, 2013, 12:22   #62
Timber Wolf
Registered
 
FALaholic #: 805
Join Date: Aug 2000
Location: Southern U.S.
Posts: 3,868
This is very interesting, thanks for the updates. I just sent an e-mail for sabots, I want to try some homebrew "reduced recoil" loads with .58 Minis out of my 3-Gun shotgun. I have a mold, think it is the Lyman 575213-OS, but am open to try others as I also have a Renegade with slow-twist .58 caliber Green Mountain barrel.
__________________
First rule of gun fighting: "have a gun!"

"Guns don't kill people. Daddys with good looking daughters do!"
Timber Wolf is online now   Reply With Quote
Old August 21, 2013, 16:44   #63
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
I emailed you back on how get them. Waiting to hear from you.

One of our sabot testers with tight barrel, 12ga Abolt, with wide lands in
the barrel, who couldn't do any good at all with our sabot and Alliant Steel
and one type of slug, had to go to IMR 4759 & different slug.
It would twist up the sabot petals. Terrible accuracy.

My guns have NEF/Sav size barrels and worked fine with Steel as well as 4759.
Petals open perfect here. The Abolt barrel about .005" smaller than NEF/Sav and
the lands over twice as wide as the NEF. And has real narrow grooves.
Guys with Nefs say sabots open fine like ours here.

He went to different Minie slug and our slow powder loads using
IMR 4759 powder up to 78-79 gr and finally got down to 2.5" group, I told him
go to max which is about 80-82 in 3" case.That barrel is like a lot of
EU made barrels and many are replacement or add on barrels in many slug guns,
and that is reason why it is so hard to get accuracy across the board in
sabot shooting in all guns--Takes a lot of work.. Another tester with NEF 12ga using
Alliant Steel with sabots got good groups like we did here. I tell guys if
problems occur go to 4759.

What was happening to sabot petals in the barrel, with the extra tight fit and
wide lands were petals twisting.. The wide lands were not cutting into the base of
sabot like in NEF/Sav210 barrels. The twist effect of rifling was on the surface
of petals, twisting them. It was not getting good hold on the sabot body. The
4759 starting slower allowed the sabot to get its spin started up to speed
with the wide land rifling and narrow grooves..It is just the opposite of
way NEF/Sav 12ga barrels are done. with narrow lands which impress into
the sabot base the way it is supposed to work..I showed pics above of the
good rifling marks impressed into our sabots.

I think after this experimenting run I feel that a lot of accuracy problems
across the spectrum of barrels are due to barrel differences, and not just
the differences in factory slugs and/or reloading components.

Here is pic of bag of our 585 cases with plain head if some need them for
wildcatting.We have quite a few. Fifteen have 585HE cases now. 585 gun
building is accelerating. We can get folks going with 100 cases, dies, and soon
a barrel; and shipping, for 750...Ed

__________________
Ed Hubel

Last edited by hubel585; August 21, 2013 at 16:52.
hubel585 is offline   Reply With Quote
Old September 15, 2013, 16:40   #64
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is picture of our 12ga sabots with the marks that the barrel lands made, marked with
black marker. The one with narrow mark is Savage barrel and one with wide mark is
an Abolt barrel. And the ones fired in Savage and NEFs with the narrow lands the marks
impressed into the plastic getting good bite and not twisting the petals. The one from abolt
he used slower powder for easier start and it open petals ok, without twisting petals like
the faster powder did for him.


..
Next is picture showing top edge of sabots. Our sabot on left you roll crimp down over
the inside of it a little . We have lots of them yet.
The other factory sabot they crimp real short and sharp
180 degree crimp down on top of it.



We see a use for modified 585 application in Indiana deer hunting. Mainly shotgun only, but
they also allow rifles with over 35cal pistol calibers; and any over 35cal rifle with a case
1.8" or shorter, usually short wildcats. So we have the the 585 HI... The I is for Indiana.
Here is picture of it next to the kinda little 500 S&W. 585 HI holds over 80 gr powder.

Next picture is a Magtech chambered for it. Gets 440gr Minie over 2,100 fps.
The .585"- .587" Minies of 440gr, 540gr, etc work in it, and they're good deer slugs
We got other guns with it going into; bolt guns, like in the last picture,
single shots and checking couple lever actions.
Might work great in MNs many guys like....Ed





__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old October 16, 2013, 09:36   #65
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
In above post we compare the top thickness of sabots
.Here is comparison of the thickness of the sides of two types of
brass 12ga cases, the RMC turned case and the thinner
Magtech drawn case. Easy to see you can't size with same dies
and sometimes you have to use different wads..



In posts earler in the thread you saw variety of wad columns with
12ga sabots and here is picture of my favorite wads to go between
seal and sabot. The white felt ones from BPI. They compress down
evenly on firing, easy to load, decent price,



You've seen the work on our 585HE posted. Folks ask what case
I made first ones from and how. Here is a sketch showing the steps
I used to make the first 585HE from long basic straight Nyati brass.
The start of the belt step I put on the case where it is thick I do it
in my case spinner lathe I made. Then case is lubed and run into
couple swaging/sizing dies and comes out formed into our belted,
straight sided, 585HE case...... It is really faster getting a big
run of cases made in a factory.




Shot a 12ga sabot load w/440 gr Minie bullet in smoothbore Rossi
in 3" case, Going about 1700... .. 4" group 3 shots at 30 yds.
Gun works fine, shoots nice. Got extra weight in the butt.
The Minie I used is a semi-round nose. If I had the ones of same length
with blunt nose, slightly heavier the group size would be smaller as
they'd be more nose heavy, be like Foster slugs..Ed
__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old December 09, 2013, 01:28   #66
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is picture of the group improvement a guy had shooting our
sabots in a real tight barrel. Actually an undersize barrel compared
to Savage and Nef barrels. Had a wide open group with shotgun
powder but made it much smaller using much more
of the slower 4759.



There is a guy now in Canada with our sabots for guys there and
other countries, and as well, he can ship back to here. He plans
on supplying the .58cal slugs also for the sabots if guys can't get
them or don't cast their own.......
Contact is- jeff.a.white at gmail.com
If things work out for him he plans on getting a bunch
our 585 cases imported for guys to get there also.

I got some factory 8ga kiln loads, 3 oz lead at 1800 in the long
barrel falling block. Got box of 25 to see how they compared to the
loads we setup.They go faster in long barrel than in short kiln guns.
Our favorite is 900gr in the 8ga wadcup at 2300, in plastic case.



Here is picture of section 585HE case showing 4 pyrodex 54cal,
60gr equivalent pellets, with a 440 gr Minie bullet.
Actual powder wt is about 185gr....Goes about 2600.
Nice cloud of smoke and really bellers out of the slow twist barrel
barrel we set up for minies.....Top pellet I tapered a little and fit it
inside the hollowbase of the bullet.That's how to get 4 pellets in....Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old December 09, 2013, 16:38   #67
Derek Wildstar
Registered
 
FALaholic #: 72549
Join Date: Oct 2013
Location: Pennsylvania
Posts: 55
You guys got any loads that might be safe out of a pump Mossberg??
Derek Wildstar is offline   Reply With Quote
Old January 01, 2014, 19:41   #68
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
12ga-- use sabots and 440-500 gr slugs, 80gr IMR 4759
or 45gr Alliant Steel.



Another use for 58cal Minie Bullets would be to setup a 24ga FH.
Minie bullets cheap to cast and buy. We use the .575-.577" in our
12ga sabot, and the .585-.587 in my 585HE. And you could use
577 NE bullets also.

For those in shotgun only areas there is a way. You can get 2.5"
Magtech brass cases, but also you can set up a 3" chamber and use
577NE 3" brass. Grafs shows some under 4 bucks each. Cheaper
than getting them made. And if you set up chamber with shotgun style
forcing cone you could shoot shorter Magtech as well as plastic cases.
Reason to use 577 cases, they are stronger solid head, last forever,
and can be run higher pressures and still last forever.
You can get barrels, 58cal at Green Mtn I think. .We got some also.

AND the first batch 585 barrels from McGowen has got here, more
will be built.They are the regular 1 to 20 twist barrels, and we have 14
that are profiled and polished, and 3 others that are straight blanks,
1 to 20 twist. And 6 slow twist barrel blanks for guys doing mainly
Minie bullet guns, and bunch smoothbore blanks...Pictures soon.

Here are couple pictures of a 585HE gun a guy is doing with nice
walnut stock. Gun has extra bedding lug and acra-glassed.
It is an Enfield and has single stack magazine.Ed



__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old January 28, 2014, 14:34   #69
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is picture of 585HE in a Montana Rifle Co. PH action.
The double stack mag for the 505 Gibbs they make works ok.
The Enfield in the Hogue stock above is done and gone.



We also had guy show us how the case can work for a
high energy subsonic, real high energy for subsonic
1600 gr at 1050 fps. 400 ft lbs. The 585HE Whisper
Anyone with some way overbore 14.9 mm necked
cases on huge actions, can make case inserts for
using our case to fire subsonic And still fire 650gr or 750 gr
at high speeds. Can't get 14.9 Russian cases, use ours in
same gun with inserts.




Break action I like, we did on a CBC by mono-blocking a 585
barrel, set up especially for Minie bullets of 440 to 540 gr.


__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old February 23, 2014, 16:33   #70
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Some guys in 12ga like to use the Magtech brass cases
but the cases being brass the sides are thinner than
plastic, and that makes loose fit in 12ga chambers.
And cases expand a lot with heavier loaded slug
loads, are harder to resize, wear out quicker.
But I found that .750 hollowbase 10ga slug fits
those cases and still chambers in regular 12ga.
chamber, it isnt a sloppy fit.

So If you have a 12ga smooth barrel with full length
backbore job, of .850" bore or bigger you could use
the Magtech brass and .850" size 10ga hollowbase slugs.
Now these .850" slugs won't go in a 12ga plastic case
and chamber in regular 12ga chamber.And you do not
fire them through 12ga regular size barrel.

Brett in MN used the a BPI AQ slugs in his full length
backbored 12ga and got fair accuracy as he said the wads
under slugs expanded a lot for a decent fit.
The 10ga slug shown in the 2.5 inch Magtech is 800 gr,
and .850" diameter. These cases will take magnum
pressure so you can get good speed, for what this short
case can hold.

It is too bad they don't make 3" and 3.5" versions.
These 2.5" cases are easier to find and much less than
others, so if needing brass ones you can rig up guns
to work with them. To build a new barreled gun in actual
12ga size, IE .729" bore, you'd make chamber to
minimum specs so cases don't over expand.
In the picture are 2 10ga slugs on right, like in the case,
and 2 12ga jacketed slugs and one 12ga lead slug left.ED






Here is the ytube URL again for our guy
shooting 585HE in his NEF----By mid summer we plan on a
pickup truck load of more 585HE cases coming in.

http://www.youtube.com/watch?v=HypaUdwQGAc
__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old March 13, 2014, 21:36   #71
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is good simple system with big hollowbase slugs to stop
the skirts from deforming, or wads getting pushed into
the hollow base. I found that dense dow foam works
good, I was using glue gun, but the dense foam is easier, cut
plugs out of foam sheet and force into the base. Make it a
tight fit, use spot of glue inside, glue that is for foam....
Trim off the foam flush..In picture is 10 ga 900gr slug
with foam pressed into the base..



How we get good 24ga plastic seals with protusion on
top that fits up inside 58cal Minie base, same bore as 24ga
and our 585HE. I get the 24ga seal by cutting apart the BPI
24ga Brush wad, getting two seals out of each.Works great
in plastic case giving a shorter column than other seals and
wads, so we can get in enough of our 4759 for good speed.
The 24ga idea is getting nicer all the time with
the variety of cheap 58cal slugs, and good 3" brass cases,
drawn cases, we didn't have to wait to get made.
And all kind of guns we can use, bolt 395 Mossbergs, single
shots of all kinds, Autos,, pumps. bolt action Savage,
even 1887 Win and Greener MKIII, bolt action JC Higgins. .



Here is picture Khan auto we setting up 24ga FH, it is 3.5"
model, has a 12ga barrel to change with. Being 3.5" it
feeds/ejects through lengthened port 3" brass 24ga cases we
made from 577NE brass. We rework back of the bolt for
slightly longer stroke.Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old April 23, 2014, 20:35   #72
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is picture of 24ga cases, loads; and some slugs and seals.
Brass cases are 3", plastic cases are 2.5". Brass 3" can be loaded
to match 577NE power.



Here is of 24ga in an 87 Win, just test gun of mine. Uses same barrels
as our 585HE, This one has slow twist for Minie bullets.Our guys
have got supply of regular and slow twist barrels.



Here is picture of the first 585HE done and shooting in Australia.
It is owned by the poster, 'tankhunter' on the AR forums.
Built by his smith who has a reamer.
Guys there can get cases from Bertram, and there will soon be three
reamers there. There is a company there now making 585 barrels,
Allan and Grant Swan. in Redbank, Queensland.....Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old May 09, 2014, 22:09   #73
Jarhead504
Registered
 
FALaholic #: 65022
Join Date: Jan 2012
Location: New Orleans Area,LA
Posts: 959
Great work Brother! I like your way of thinking. Keep up the good work.

Jarhead
Jarhead504 is offline   Reply With Quote
Old August 17, 2014, 01:23   #74
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Finally got back to forums.Been busy with 24ga FH and 585HE
and getting 585HE cases made, as many as possible...

We are now working a bit with 24ga FH and here is picture
of it with our 585HE case. Both use same bullets/slugs, same
bore barrels. Main use difference, 24ga FH easy setup in break
actions and 585HE in bolt actions and falling blocks.



Picture of non-discarding 585/24ga sabot cup I found that holds
458 bullets and slugs tight. It had hammerhead type slug in it that
was pulled out, wouldn't stay in tight after pulled. Sabot was a loose fit
in 20ga, though made for 20ga, but small, so I shrunk the bottom rib,
fits perfect, super tight, in 24ga and 585HE. A press in fit gives
good resistance for good ignition.



Here is another 24ga/585 sabot that holds .452" 45cal pistol
bullets. Made by Hornady for 58cal Muzzle loaders..
With 250 gr bullet in 585HE hot load will go about mach 4.



Here is easy way to weight plastic stocks with hollow butts, use rubber
coated computer mouse balls, weight comes out perfect without being
too heavy if using that much lead.And coating keeps them quiet, and
we hold them in with piece dense foam under butt pad....Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old September 10, 2014, 13:41   #75
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
First AUS buffalo killed by 585HE. By Tankhunter with his Ruger #1.

If you use closeup on picture, you see loaded round on the buffs hide

next to the 585HE Ruger #1.... A nice heavy barreled gun..Ed




I put the 585 in a Savage 112, lots of room lengthwise, figuring out an
extractor is a problem, but then got a look at the savage 212, the 12 ga
one with big diameter bolt and locking lugs. Its locking lugs are bigger
than the lugs in a big PH bolt action. So one day will do one
on a Savage 212, and adjusting extractor to fit no problem...Ed

__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Old October 25, 2014, 12:45   #76
hubel585
Registered
 
FALaholic #: 64718
Join Date: Nov 2011
Location: Brinton, MI
Posts: 84
Here is picture of 585HE 100 cases loaded, CEB solid nose bullets
and hollowpoints. This bullet is a turned solid with wide meplat
or wide hollowpoint. .



Here is picture of triball loads that fellows like for deer and hogs,
and just general tear em up fun, with using BPGS seal to improve
sealing under what are heavier loads. The balls are .600" and
315gr. each. The wadcup is a TUPRW123 that Precision sells.



I need a bunch of empty 3.5" 20ga plastic cases.


Our 585 caliber is modern bolt action continuance of the 577 Nitro
Express rimmed case, that many big game hunters like, usually
set up in double rifles. It has an interesting history, from the old 24ga
size to 577NE, to 585 Nyati with G&A picture of Ross Seyfreid
shooting one in a Ruger #1 under recoil knocking his shooting glasses
off, to the Trex of internet fame knocking guys over with recoil,
to our 585HE the strongest yet.

The 577NE is an offshoot of 24 gauge caliber paper cases, only they went
eventially to brass cases. Back in the 1860-70s, starting first with short
cases and black powder, cases built like shotgun cases, called the
577 Snider, then going to coiled brass cases, still with black powder,
then on to drawn brass cases, called 577 BP Express. then to 3"
and other longer cases with smokeless. The Snider started out with a bullet
of .570" diameter and through the progression to the 577NE bullet
diameter ended up at .585". This general bore diameter of cartridge guns
and muzzle loaders, it is really interesting on how they developed
and were used by military and then hunters over the years. The Snider
was necked down to make the 577-450 , a military round used all
over the British Empire, by the tens of millions.

Bases of both 24ga and 577NE are about the same. Now we have made a
24ga FH, a slight regression to earlier times, by taking 577NE brass, and
reducing rim diameter to 24ga specs. Two minute job. And
stamp the caseheads 24 ga.

For shotgun upgrading in power and range, It is all about increasing
the power in easy to find brass cases, stronger actions, and finding
reasonable price rifled barrels. Same barrels we found for 585, work for 24ga.
The 577NE brass we make 24ga drawn cases from, for example are
about a third the cost of 600NE brass, or getting turned 24ga cases made.
We could use 24ga thin cases but they are a pain, expand way too much,
with slug loads which makes resizing without crumpling cases a problem.

Info about the power in types of guns normally set up with 24ga FH,
break actions, bolt shotguns,etc. In thin brass 24ga case, 440gr slug
goes 1500, with about 2000 ft lbs, that's in a 2.5" Magtech brass case.
Now using the better, heavier 3" brass we got, we can increase speed
to 1750 fps increasing energy 50%, going to 2000 fps about doubles
energy. And going to 2300 which good brass holds ok, in heavy barrel
gun, gets us near 2 1/2 times the energy. About 37-40,000 psi which the
actions hold in this smaller diameter case, compared to 12 gauge size.
So makes relatively smaller bore shotgun, 24ga, with 458WIN power.
.Perfect with Minie bullets. Perfect for deer and hogs, bear, etc.

Great for slug hunting in shotgun only areas. We mark barrels 24ga
and cases 24. A decent case that is complimentary to our 585HE....Ed
__________________
Ed Hubel
hubel585 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 10:44.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
©1998-2012 The FAL Files