![]() |
![]() |
#1 |
Registered
FALaholic #: 1273 Join Date: Oct 2000
Location: Colorado/Utah
Posts: 1,373
|
Got a VZ58 kit, What is missing?
I know I'm late to the VZ game, but it was a now or never. I broke down and got a kit from Arms of America.
I've got a fixed stock on the way. I believe I'm missing the 2 pins for the front sight. I also believe I'm missing the pin and detente that retain the captive pin for the dust cover. I am unsure of what else may be missing, so I'm providing 2 detail pictures and an over view picture. Please advise. Thanks ![]() ![]() ![]() Ok looks like I have the top cover detente after all, its just longer than I'd expected. looks like it doesn't use a spring??? Any idea where to get a new (over sized) barrel pin? and the trigger guard rivets? Last edited by Ghost; June 04, 2018 at 21:39. |
![]() |
![]() |
![]() |
#2 | |
Registered
FALaholic #: 13827 Join Date: Mar 2004
Location: Colorado Springs, CO
Posts: 15,563
|
Quote:
The replacement barrel pins that Czechpoint supplies for building kits with the D-Technik receiver is about 0.158" The receiver is dimpled to indicate where the barrel pin hole is milled/drilled. The long receiver cover detent has it's bottom end resting on the long finger of the trigger feather spring. Looking down into the receiver from the top with the front forward, the right hand finger extends rearward into the opening at the rear of the receiver and the detent comes down it's hole from the top and rests on this spring. Forrest |
|
![]() |
![]() |
![]() |
#3 |
Registered
FALaholic #: 1273 Join Date: Oct 2000
Location: Colorado/Utah
Posts: 1,373
|
Thank you ftierson,
I think some things would be more self evident if I had a receiver in hand. I just missed out on the CNC Warrior run. Hoping they do another run. From what I gather the FCG I chose will be contingent on the receiver I find? Original axis pins vs. proprietary. |
![]() |
![]() |
![]() |
#4 |
Registered
Contributor
FALaholic #: 64403 Join Date: Oct 2011
Location: North Carolina
Posts: 2,122
|
If you want to do a test fit of all the parts you have on the cheap, to make sure you are not missing anything,
https://www.clearviewinvest.com/akdu...composite.aspx
__________________
All I'm really asking for here is a knife that will not jam and a unicorn that doesn't need sharpening. Will_Power It's been my experience that all you really need to harvest a deer is a car. They come right through the windshield just fine. 357ross That poop is priceless. MFC |
![]() |
![]() |
![]() |
#5 | |
Registered
FALaholic #: 1273 Join Date: Oct 2000
Location: Colorado/Utah
Posts: 1,373
|
Quote:
I got in on the very end of the new CNC warrior receiver run, so I've got a receiver shipping today! |
|
![]() |
![]() |
![]() |
#6 |
Registered
Contributor
FALaholic #: 64403 Join Date: Oct 2011
Location: North Carolina
Posts: 2,122
|
Congratulations, Ghost. I was not even aware CNC warrior was doing another run. He makes good stuff but his prices make IMBEL receivers look cheap at times.
![]()
__________________
All I'm really asking for here is a knife that will not jam and a unicorn that doesn't need sharpening. Will_Power It's been my experience that all you really need to harvest a deer is a car. They come right through the windshield just fine. 357ross That poop is priceless. MFC |
![]() |
![]() |
![]() |
#7 |
Registered
FALaholic #: 1273 Join Date: Oct 2000
Location: Colorado/Utah
Posts: 1,373
|
I almost missed out on it. Now I need to figure out the tooling I'll need to get it all together, primarily pressing the barrel. Actually looks like a pretty easy build.
|
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|