The FAL Files  

Go Back   The FAL Files > General Information > Reviews - products, services, and sellers

Notices

Reply
 
Thread Tools Display Modes
Old July 28, 2017, 18:38   #1
gunplumber
Arrogant Bastard
Gold Contributor
 
gunplumber's Avatar
 
FALaholic #: 96
Join Date: Jul 2000
Location: Surprise, AZ
Posts: 24,258
Review - DSA - FAL Receiver - Type 1, 2, 3 & F

DSA Receiver Review
DSA quality has dropped significantly over the last several years, and their Brit cut L1A1s have been really bad. Yet when I post my comments and photographic evidence, there are still some DSA fanboys and paid shills who get their panties in a bind – maligning me for having the discourtesy to actually report my findings with photographic documentation.

So this is kindof a journal of my build notes. With 20 or so DSA receivers in for builds, I thought this a good time to document them consecutively, hopefully allowing for some comparisons that might reveal a pattern. I doubt DSA gives a shit, but if they do, perhaps my findings will motivate improvement.

Summary
The F marked type 1s are pretty good.
None of the Type 2s would accept a mag and had significant problems with locking shoulder..
The type 3 was really bad all around

I'll update this as I refine my notes and progress to testfire.

If a subsequent receiver had the same problem as the previous, I did not photograph it.

DSA 34704 Type 2 "F"
overall appearance: pass
receiver cover: fail – clearance front at 1-2 o'clock
e-block rear: pass
eblock at hinge: pass
e-block at rail: pass
bolt carrier to rail: pass. slight binding R side front, withn acceptable range
hinge hole: pass
hinge width: pass
Lockup: pass – barely. almost bottoms out
BHO: pass
mag catch screw: pass
mag catch: pass
mag fit: pass
ChH rail: pass
CH nut: pass
timing: pass 10:30
LS dogleg: fail. Tapers from .307 front to .291 rear. sand shoulder
LS hole: fail – undersize, flapsand.
LS: .255
b/bc fit: pass. – barely. Bolt binding on rail to left of ejector. ragged finish. file smooth
http://www.arizonaresponsesystems.co...sa34704-01.jpg

DSA 34781 Type 1 "F"
ChH rail: pass
CH nut: pass
mag catch screw: pass
mag catch fit: pass
mag fit: pass
BHO: pass
hinge hole: pass
lockup: pass. e-block very slight friction, inconsequential, light binding last 1/8" stepped rails
timing: pass StG barrel 10 o'clock
b/bc fit: pass. Some binding at e-block, but e-block not proud. Forced it a few times, light filing, now smooth. Small irregularity front rails right before feed ramps – narrower.
LS dogleg: pass
LS hole: pass
LS: .256
http://www.arizonaresponsesystems.co...sa34781-01.jpg
http://www.arizonaresponsesystems.co...sa34781-03.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa34781-10.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa34781-11.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa34781-12.jpg

DSA 34844 Type 1 "F"
ChH rail: pass
CH nut: pass
mag catch screw: pass
mag catch: pass
BHO: pass
mag fit: pass
timing: pass (FN). Note: DSA G1 barrel hand timed to 12:00
hinge hole: pass
Lockup: pass
LS dogleg: pass
LS hole: pass
LS: .264
b/bc fit: pass. Some binding last 1/8" from step in rail. Dremel from front. New standard - always dremel these steps from front before even trying fit.
finished rifle: http://www.arizonaresponsesystems.co...sa34844-10.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa34844-11.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa34844-12.jpg

DSA 35184 Type 3 non F
ChH rail: pass
CH nut: pass
mag catch screw: fail - won't even start – retapped
BHO: pass
mag catch: pass
hinge hole: pass
lockup: pass. Little binding at e-block
mag fit: epic fail – not even close to fitting. machine whole front and cut mag notch deeper
barrel threads: fail – too tight for my FN test barrel. Recut.
LS dogleg: pass
LS hole: pass - tight, but ok.
receiver note: excess metal left front – incompletely machined.
LS .256
b/bc fit: pass - step in rails created some binding (see above), but not significant – filed flat from front.

http://www.arizonaresponsesystems.co...sa35184-01.jpg
http://www.arizonaresponsesystems.co...sa35184-02.jpg
http://www.arizonaresponsesystems.co...sa35184-03.jpg
http://www.arizonaresponsesystems.co...sa35184-04.jpg
http://www.arizonaresponsesystems.co...sa35184-05.jpg
http://www.arizonaresponsesystems.co...sa35184-06.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35184-10.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35184-11.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35184-12.jpg

DSA 35614 Type 2 No F
ChH rail: pass
CH nut: pass
BHO: pass
mag catch screw: pass
Mag catch: pass
mag fit: fail – can be forced in. machine front of mag well and cut notch deeper
e-block: fail - significant gap
b/bc fit: fail. rails stepped up. clean up from front.
timing: pass FN and StG barrels. 10:30
LS dogleg: fail Dog leg undersize.
LS hole: fail. hole significantly undersize. Forces end of LS to cant forward. Flap sanded from left.
LS: 256"
finished rifle: http://www.arizonaresponsesystems.co...sa35614-10.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35614-11.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35614-12.jpg

DSA 35656 Type 2 non F
ChH rail: pass
CH nut: pass
mag catch screw: pass
BHO: pass
mag fit: fail - machined
hinge hole: pass, but very tight - flap sand
lockup: pass
e-block: fail, gap
mag fit: fail
timing: pass FN short 10:00 IMBEL 10:30
b/bc fit: pass - rail step but IMBEL b/bc still cleared. Removed anyway.

http://www.arizonaresponsesystems.co...sa35656-01.jpg
http://www.arizonaresponsesystems.co...sa35656-02.jpg
http://www.arizonaresponsesystems.co...sa35656-03.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35656-10.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35656-11.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35656-12.jpg

DSA 35660 Type 2 non F
ChH rail: pass
CH nut: pass
BHO: pass (tight)
e-block: fail (gap)
mag catch screw: pass
mag fit: fail. Mag well significantly undersize, machining front sill requires mags to be forced in. even a DSA 30rd mag would not fit! Pulled e-block, machined underside of rails, machined step in front of e-block. Mags now fit!
bho: pass (tight)
e-block: fail gap
timing: pass
lockup: pass
LS 256
LS dogleg: fail – way undersize, dogleg not parallel and way undersize – had to machine rather than just sanding dogleg a bit.
LS hole: fail - undersize on L

http://www.arizonaresponsesystems.co...sa35660-01.jpg
http://www.arizonaresponsesystems.co...sa35660-02.jpg
http://www.arizonaresponsesystems.co...sa35660-03.jpg
http://www.arizonaresponsesystems.co...sa35660-04.jpg
http://www.arizonaresponsesystems.co...sa35660-05.jpg
http://www.arizonaresponsesystems.co...sa35660-06.jpg
http://www.arizonaresponsesystems.co...sa35660-07.jpg
http://www.arizonaresponsesystems.co...sa35660-08.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35660-10.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35660-11.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35660-12.jpg


DSA35684 Type 2 no F
ChH rail: pass
CH nut: pass
mag catch screw: fail. retap
BHO: pass
mag catch: pass
mag fit – fail. machine mag well.
hinge hole: fail – flap sand
lockup: pass
timing: pass
b/bc fit: pass - slight binding on step in rails – file smooth
e-block: fail, gap
LS dogleg: fail, dogleg not parallel & undersize. – machine.
LS hole – fail, way undersize L side,
LS .257
http://www.arizonaresponsesystems.co...sa35684-01.jpg
http://www.arizonaresponsesystems.co...sa35684-02.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35684-10.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35684-11.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa35684-12.jpg

DSA 36170 Type 2 No F
ChH rail: pass
CH nut: pass
mag catch screw: fail – couldn't even start, retap.
BHO: pass
mag catch: pass
hinge hole: pass
lockup – fail - failed with IMBEL, DSA aluminum and NOS para lowers. receiver long.
hinge width: fail bad machining too tight
mag fit: fail - machine.
timing: pass - except for last 1/4 turn binding. chased. inconsequential
e-block: fail, gap
LS dogleg: pass
LS hole: FAIL way undersize, couldn't even start it
LS: .257
Para Carrier DSA: fail – no fp clearance. Could not install any bolt with FP installed. Ruined before pic, but it was just a single straight ramp, no bulge for the FP like on the IMBEL next to it. Opened up with 3/8" ball endmill.
http://www.arizonaresponsesystems.co...sa36170-01.jpg
http://www.arizonaresponsesystems.co...sa36170-02.jpg
http://www.arizonaresponsesystems.co...sa36170-03.jpg
http://www.arizonaresponsesystems.co...sa36170-04.jpg
http://www.arizonaresponsesystems.co...sa36170-05.jpg
http://www.arizonaresponsesystems.co...sa36170-06.jpg
http://www.arizonaresponsesystems.co...sa36170-07.jpg
http://www.arizonaresponsesystems.co...sa36170-08.jpg
http://www.arizonaresponsesystems.co...sa36170-09.jpg
http://www.arizonaresponsesystems.co...sa36170-10.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa36170-11.jpg
finished rifle: http://www.arizonaresponsesystems.co...sa36170-12.jpg
(replica, still tweaking the camo)

DSA R1046 Type 1 "F"
e-block rear: pass – no gap
e-block at rail: pass – flush
e-block at hinge: pass – flush
hinge hole: pass
hinge width: pass
lockup: pass (sort-of) dust shield binds. Hinge area not rounded like on IMBEL, causing full contact with plate. I rounded it out. Not ready to bitch too much over this because some dust shield plates are higher than others, and as you can see (photo pending) there is still sometimes a light drag on a factory correct contour. Still, something that DSWA should look at (if they cared). Also, the receiver lock bottomed out. I will examine thi n reassembly to see if a different receiver lock will give the correct gap. It's possible the IMBEL receiver lock is excessively worn.
BHO: pass
mag catch: pass
mag catch screw: pass
mag fit: pass. (photo pending). There was a noticeable relief on this recevier to either side of the mag notch, extending to the top corners. This is the cut I add to receivers where the mag does not fit. So why is it not on the others? On the others it's a straight pass across the mag notch. This binds on the front top corners of the mag and prevents the rear from locking.
carry handle nut thread: pass
barrel thread: pass
barrel timing: pass (10:30)
bolt & carrier: pass Still has the step but on two bolts was not enough to bind. Removed anyway.
locking shoulder dogleg: pass (barely). Still slightly tapered from .305 to .291. .007 is a lot for an interference fit, so I sanded the locking shoulder instead of machining the recess.
locking shoulder hole: pass
locking shoulder size: fail (.249, tight close on .308)
receiver cover: pass


Next up will be the DSA L1A1 Brit pattern.
__________________
T. Mark Graham, Master Gunsmith
Arizona Response Systems, LLC

Last edited by gunplumber; July 02, 2018 at 13:00.
gunplumber is offline   Reply With Quote
Old July 28, 2017, 21:12   #2
Boris
Registered
 
FALaholic #: 61969
Join Date: Nov 2010
Location: Ga
Posts: 13
It sucks that there are not better options out there right now. I hate to say it but I just bought a DSA FAL SA58 FORGED British Pattern L1A1 Carry Handle Cut Receiver. That I hope you'll build me a L1A1 when I get back to the States in a month?
Boris is offline   Reply With Quote
Old July 28, 2017, 21:31   #3
coltrunner
Member
Bronze Contributor
 
coltrunner's Avatar
 
FALaholic #: 7113
Join Date: Aug 2002
Location: Hoschton, Ga.
Posts: 379
Thanks Mark for all the good info and the time you put in to.
coltrunner is offline   Reply With Quote
Old July 28, 2017, 22:10   #4
308/223shooter
FALAholic enabler
Gold Contributor
 
308/223shooter's Avatar
 
FALaholic #: 15405
Join Date: Sep 2004
Location: pacific northwest
Posts: 6,190
Quote:
Originally Posted by coltrunner View Post
Thanks Mark for all the good info and the time you put in to.
Second that. Too bad Dave won't take your advice and get his house in order. I'm in need of a Brit cut receiver, but don't want cast out of spec crap.
__________________
What if the Mystery Babalon described in Revelation, which is destroyed by the nations of the North, is actually America?

The biggest problem with religion is those who claim to know Jesus, then turn around and deny Him with their lifestyle. That is what a unbelieving world, simply finds unbelievable.

Before you die, you should have a will with extra copies. The old saying "No one will screw you faster than family" is bloody well true.
308/223shooter is online now   Reply With Quote
Old July 28, 2017, 22:11   #5
idsubgun
"Comfortably Numb"
Bronze Contributor
 
idsubgun's Avatar
 
FALaholic #: 3100
Join Date: Apr 2001
Location: In the woods of Missouri
Posts: 10,355
As someone that machined stuff for several decades, this is simply piss-poor quality control and piss-poor machinists doing the machining.

And it's so simple to make some adjustments to the set-up, program and/or tooling.

Their machine shop just isn't paying attention to details. And the sad thing is people have been bitching about their receivers but DSA simply doesn't care. It seems that way, anyway........
idsubgun is offline   Reply With Quote
Old July 28, 2017, 22:41   #6
embatp
What? Me AR?
Silver Contributor
 
embatp's Avatar
 
FALaholic #: 39856
Join Date: Nov 2008
Location: Behind enemy lines...
Posts: 4,155
Mark....I know these issues have been found on receivers that came in with kits for builds.....but will repairing these receivers be a service you may provide in the future to owners of receivers in these serial ranges?
__________________
"only he is lost who gives himself up for lost"

Last edited by embatp; July 29, 2017 at 01:10.
embatp is online now   Reply With Quote
Old July 29, 2017, 07:13   #7
G3isMe
Registered
Bronze Contributor
 
G3isMe's Avatar
 
FALaholic #: 6530
Join Date: May 2002
Location: Clinging to my Guns and Religion
Posts: 5,234
Thanks for posting this review. What is really disconcerting is the problems you have identified look like they could have been lifted from my build journals. I have had these very same problems on almost all of my newer DSA non-F receivers. ........

.
__________________
.
“When you don't know how many you have... you might have enough........" 12v71
G3isMe is online now   Reply With Quote
Old July 29, 2017, 09:32   #8
gunplumber
Arrogant Bastard
Gold Contributor
 
gunplumber's Avatar
 
FALaholic #: 96
Join Date: Jul 2000
Location: Surprise, AZ
Posts: 24,258
Quote:
Originally Posted by embatp View Post
Mark....I know these issues have been found on receivers that came in with kits for builds.....but will repairing these receivers be a service you may provide in the future to owners of receivers in these serial ranges?
I don't know, because I have to do the build to find the problems. If it's already barreled, then I have to pull the barrel, which is more work than starting with a virgin build. So I don't know that I can do it for less than the cost of a complete build. It would start at the $350 rebuild price.

What has been helpful about doing them in sequence, and writing everything down (instead of just cursing, sputtering, and kicking the wall), is that now I can anticipate problems, rather than discovering them at the testfire range and losing all that work.

I have not yet charged extra for DSA builds, but it looks like I'm either going to have a "Out-of-spec DSA surcharge" or charge everyone more and then offer a discount for IMBELs, LMTs, or other quality in-spec receivers. It is currently costing me over $150 in shop time - above the price of the build - to correct or work around DSA's defects. And that does not count the days of experimenting I did to work out these techniques. I can't continue to eat those expenses.

GF suggested last night, that a pattern of defects across multiple people in multiple states, is a class-action lawsuit waiting to happen. But I don't want DSA sued out of business for their defective crap - I want their defective crap fixed!

And the part that has me so angry and frustrated and disappointed, is I perform all these checks in 5 minutes on a virgin receiver, with a couple factory parts, and a few home-made gauges. Just like I taught Entreprise when they flew out to have me evaluate their last receiver run. I gave them all the different GO/NOGO options for checking a receiver. Nothing fancy, just methodical and disciplined procedures. But they apparently never bothered to use them!

While quality control checks will reveal problems, they don't change The Chicago Way. DSA needs a cultural change, starting with Dave. He has knowingly and willingly shipped defective products for a long time. Nothing is going to change until the man at the top is replaced by someone with integrity. And if the board of directors is unwilling to do that (because they too represent The Chicago Way), there will be no change.

Or someone else needs to come along and make good receivers. But I doubt it would be profitable anymore. But any serious contender can have all the tech support I've collected over the years.
__________________
T. Mark Graham, Master Gunsmith
Arizona Response Systems, LLC

Last edited by gunplumber; July 30, 2017 at 13:35.
gunplumber is offline   Reply With Quote
Old August 09, 2017, 12:06   #9
lew
Registered
Bronze Contributor
 
lew's Avatar
 
FALaholic #: 16727
Join Date: Jan 2005
Location: Phoenix, AZ
Posts: 7,814
Quote:
Originally Posted by gunplumber View Post
DSA Receiver Review
locking shoulder dogleg: pass (barely). Still slightly tapered from .305 to .291. .007 is a lot for an interference fit, so I sanded the locking shoulder instead of machining the recess.
This is the same problem I had on both of my R1 receivers- R1034 and R1054. I had DSA take care of the issue on both, which they did, to their credit.
__________________
Statism: Ideas so great, they're mandatory.

There is not a problem that government cannot make worse.
lew is online now   Reply With Quote
Old August 09, 2017, 13:12   #10
gunplumber
Arrogant Bastard
Gold Contributor
 
gunplumber's Avatar
 
FALaholic #: 96
Join Date: Jul 2000
Location: Surprise, AZ
Posts: 24,258
Quote:
Originally Posted by lew View Post
This is the same problem I had on both of my R1 receivers- R1034 and R1054.
But according to R1 Shooter's drunken ravings on Facebook - my review is "bullshit". How is it possible for you to have the same problem? (sarcasm)

That being said, the F marked R series and type 1s are noticeably superior to the type 2s, which are also superior to the type 3s.
__________________
T. Mark Graham, Master Gunsmith
Arizona Response Systems, LLC
gunplumber is offline   Reply With Quote
Old August 10, 2017, 12:26   #11
lew
Registered
Bronze Contributor
 
lew's Avatar
 
FALaholic #: 16727
Join Date: Jan 2005
Location: Phoenix, AZ
Posts: 7,814
Quote:
Originally Posted by gunplumber View Post
But according to R1 Shooter's drunken ravings on Facebook - my review is "bullshit". How is it possible for you to have the same problem? (sarcasm)

That being said, the F marked R series and type 1s are noticeably superior to the type 2s, which are also superior to the type 3s.
Yeah, well what the hell do you know?

It's amazing that R1Shooter still thinks folks like us want to see DSA tank when the very opposite is the intention. His antics remind me of Baghdad Bob.
__________________
Statism: Ideas so great, they're mandatory.

There is not a problem that government cannot make worse.
lew is online now   Reply With Quote
Old August 10, 2017, 12:57   #12
AspektZA
Registered
 
FALaholic #: 76416
Join Date: Aug 2015
Location: Houston, Tx
Posts: 37
Quote:
Originally Posted by lew View Post
Yeah, well what the hell do you know?

It's amazing that R1Shooter still thinks folks like us want to see DSA tank when the very opposite is the intention. His antics remind me of Baghdad Bob.
I think it illustrates a deep problem with US manufacturing.

American labor costs are high, but automated machines have identical costs where ever they are.

A product like a cloned firearms receiver with intricate details is something that can't necessarily be 100% automated to reduce labor costs.

DSA doesn't want to pay high labor costs for QC, finishing work, etc., and instead has left it up to the mad souls who use their parts.

US manufacturers have to automate as much as possible to be competitve, but that requires significant investment - something DSA might not necessarily be pursuing since their market is relatively captive.
AspektZA is offline   Reply With Quote
Old August 10, 2017, 18:03   #13
357ross
Registered
 
FALaholic #: 47543
Join Date: Jul 2009
Location: Utah
Posts: 4,951
I think in this case dsa has made a decision to let the fal parts go. The machinery to make receivers is probably wearing out, and it wouldn't make economic sense to spend money on a dying market. Besides, there are lucrative government contracts to think about. Dsa's quality control (and Coonans for that matter) decline is very predictable.
357ross is online now   Reply With Quote
Old September 08, 2017, 12:54   #14
308/223shooter
FALAholic enabler
Gold Contributor
 
308/223shooter's Avatar
 
FALaholic #: 15405
Join Date: Sep 2004
Location: pacific northwest
Posts: 6,190
Ok, dsa is going to take it back in for repair. Hope you don't mind Mark, but posting this for a timeline. Let's see how long before it's returned, and if they actualy repair it.
__________________
What if the Mystery Babalon described in Revelation, which is destroyed by the nations of the North, is actually America?

The biggest problem with religion is those who claim to know Jesus, then turn around and deny Him with their lifestyle. That is what a unbelieving world, simply finds unbelievable.

Before you die, you should have a will with extra copies. The old saying "No one will screw you faster than family" is bloody well true.
308/223shooter is online now   Reply With Quote
Old September 08, 2017, 13:48   #15
gunplumber
Arrogant Bastard
Gold Contributor
 
gunplumber's Avatar
 
FALaholic #: 96
Join Date: Jul 2000
Location: Surprise, AZ
Posts: 24,258
No problem. I've been calling out defects in DSA's products for years and they've been ambivalent at best - preferring spin control to fixing the problems. And so Dave Selvagio continued to knowingly and willingly sell these defective products. (Keep an eye on that phrase, you're going to see a lot more of it soon).

Apparently, DSA did not expect their potential customers to do any research, but to blindly swallow bullshit from people like their representative (paid liar) R1shooter (Daniel Lombard). Perhaps someone ready to hand out a "lucrative government contract" has had second thoughts, after reading my well documented analysis, and the reports from my fellow enthusiasts that confirm my observations.

Recent events suggest that I've finally gotten their attention - although their reaction is going to cost them far more than simply fixing their shit. These are going to be "interesting times."
__________________
T. Mark Graham, Master Gunsmith
Arizona Response Systems, LLC
gunplumber is offline   Reply With Quote
Old September 08, 2017, 14:28   #16
brunop
Refresh Key Masher
Gold Contributor
 
brunop's Avatar
 
FALaholic #: 17136
Join Date: Mar 2005
Location: Oregon
Posts: 12,777
Mark -

I've been arguing for years that you should be a Mod here in the gunsmithing sub-forum as you requested/offered.

Thanks for sharing publicly the documentation you've done over the years. Big service to the community, and a bitchin' straight jab to the eye of the douchenozzles who would (continue to) rip us off.
__________________
"How we burned in the prison camps later thinking: what would things have been like if every security operative, when he went out at night to make an arrest, had been uncertain whether he would return alive and had to say good-bye to his family? Or if during periods of mass arrests people had simply not sat there in their lairs, paling with terror at every step on the staircase, but had understood they had nothing to lose and had boldly set up in the downstairs hall an ambush of half a dozen people with axes, ham- mers, pokers, or whatever else was at hand. . . . The Organs [police] would very quickly have suffered a shortage of officers . . . and notwithstanding all of Stalin‘s thirst, the cursed machine would have ground to a halt." - A. Solzhenitsyn, Gulag Archipelago
brunop is online now   Reply With Quote
Old September 08, 2017, 14:47   #17
OLDMANPBK
Veteran Member
Silver Contributor
 
OLDMANPBK's Avatar
 
FALaholic #: 69978
Join Date: Mar 2013
Location: Medina, Ohio
Posts: 1,054
Quote:
Originally Posted by gunplumber View Post
Recent events suggest that I've finally gotten their attention - although their reaction is going to cost them far more than simply fixing their shit. These are going to be "interesting times."
It sounds like DSA is trying to shoot the messenger.
__________________
"The truth is incontrovertible; malice may attack it, ignorance may deride it, but in the end, there it is. "
-Winston Churchill-

"Is life so dear, or peace so sweet, as to be purchased at the price of chains and slavery?"
-Patrick Henry-

Inside every progressive is a totalitarian screaming to get out.
OLDMANPBK is online now   Reply With Quote
Old September 09, 2017, 10:32   #18
gunplumber
Arrogant Bastard
Gold Contributor
 
gunplumber's Avatar
 
FALaholic #: 96
Join Date: Jul 2000
Location: Surprise, AZ
Posts: 24,258
Quote:
Originally Posted by OLDMANPBK View Post
It sounds like DSA is trying to shoot the messenger.
Yep. Dave is being very foolish. Thus far I've only been growling. Now he is threatening me with legal action for "defamation". My sister is an attorney, and my GF also went to law school (hasn't taken the AZ Bar yet). And I'm pretty well educated too, although my background is in international law and national security. Does this dumbass really think that a grammar nazi like myself doesn't know exactly what I'm writing? Does he think I can't back up every word?

GF suggests "Bring it, Bitches!" should only be part of the response, and not the whole response.

So I spent yesterday morning doing a quick search on DSA's defective products, when they were first aware of them, and how long after they continued to sell them - holy shit! There were dozens of pages of stuff I'd forgotten about.

So yeah, this attempt to silence and intimidate me is going to have the opposite effect. And the publicity is going to cost DSA dearly. Which is too bad. Because until now, I only wanted to help them produce a good receiver, even if I had to shame them into doing so.

Oh, and now R1Shooter is challenging me to a fist fight. Hahahahahahha. Yep. Interesting times.
__________________
T. Mark Graham, Master Gunsmith
Arizona Response Systems, LLC

Last edited by gunplumber; September 09, 2017 at 10:38.
gunplumber is offline   Reply With Quote
Old September 09, 2017, 11:46   #19
OLDMANPBK
Veteran Member
Silver Contributor
 
OLDMANPBK's Avatar
 
FALaholic #: 69978
Join Date: Mar 2013
Location: Medina, Ohio
Posts: 1,054
This is sad and infuriating at the same time. DSA's solution to their obvious QC problems is a lawsuit and a fistfight . Well, I can't buy fewer of their products than I already do but I would donate to the GP legal defense fund if need be.
__________________
"The truth is incontrovertible; malice may attack it, ignorance may deride it, but in the end, there it is. "
-Winston Churchill-

"Is life so dear, or peace so sweet, as to be purchased at the price of chains and slavery?"
-Patrick Henry-

Inside every progressive is a totalitarian screaming to get out.
OLDMANPBK is online now   Reply With Quote
Old September 24, 2017, 16:57   #20
slojet100
Registered
 
FALaholic #: 79478
Join Date: Apr 2017
Location: Bayville N.J.
Posts: 5
R1048 Build need help and opinion

Hi Guys, I'm new to all of this so here it goes. My DSA Forged R receiver seems to be pretty good. Barrel Timed 1100 , had to re-tap screw for mag lock bolt release Fit dust cover, same problem gunplumber stated about the locking lever position . I tried three lowers and found one that locks tight but has no more room to wear. Do they make an over size lock as am confused as to what to do if it loosens up. Locking shoulder dog leg hole is a little tapered but I can resolve easily, of course I need a .252 sized locking shoulder so if someone has one for sale let me know. Also mag well is a little tight at both sides . The mags I have work but are a little difficult to slide in. I Can polish the sides of the mag well but don't know if I should. Any Ideas for these problems. My other cast rifle: DSA resolved the problems for me but it shoots low . I filed the front sight but need to test fire. So far nothing major just work. Hopefully the rest will go ok
slojet100 is offline   Reply With Quote
Old September 24, 2017, 18:01   #21
FriendBesto
Registered
Contributor
 
FriendBesto's Avatar
 
FALaholic #: 77523
Join Date: Mar 2016
Location: Beaverton, Oregon
Posts: 192
North Freedom Engineering has oversized frame locks.
FriendBesto is online now   Reply With Quote
Old September 24, 2017, 19:44   #22
slojet100
Registered
 
FALaholic #: 79478
Join Date: Apr 2017
Location: Bayville N.J.
Posts: 5
Thanks I appreciate that info
Frank
slojet100 is offline   Reply With Quote
Old September 25, 2017, 09:11   #23
gunplumber
Arrogant Bastard
Gold Contributor
 
gunplumber's Avatar
 
FALaholic #: 96
Join Date: Jul 2000
Location: Surprise, AZ
Posts: 24,258
Quote:
Originally Posted by FriendBesto View Post
North Freedom Engineering has oversized frame locks.
Excellent product. John had better do another run, because every Coonan I've done this month has required one, as well as most of the DSAs.
__________________
T. Mark Graham, Master Gunsmith
Arizona Response Systems, LLC
gunplumber is offline   Reply With Quote
Old September 25, 2017, 14:57   #24
slojet100
Registered
 
FALaholic #: 79478
Join Date: Apr 2017
Location: Bayville N.J.
Posts: 5
Mark Do you use the .010 or .020 oversize?
slojet100 is offline   Reply With Quote
Old September 25, 2017, 15:03   #25
gunplumber
Arrogant Bastard
Gold Contributor
 
gunplumber's Avatar
 
FALaholic #: 96
Join Date: Jul 2000
Location: Surprise, AZ
Posts: 24,258
It depends

If the receiver lock lever is touching the grip (horizontal) or touching the recoil plate (vertical), and has no movement; that is, it is hard against it, it is usually an OS-2.

If it is touching but can be pushed up or back slightly, or is just barely not touching, then an OS-1
__________________
T. Mark Graham, Master Gunsmith
Arizona Response Systems, LLC
gunplumber is offline   Reply With Quote
Old September 26, 2017, 14:01   #26
gunplumber
Arrogant Bastard
Gold Contributor
 
gunplumber's Avatar
 
FALaholic #: 96
Join Date: Jul 2000
Location: Surprise, AZ
Posts: 24,258
added 34704, type 2 "F"
__________________
T. Mark Graham, Master Gunsmith
Arizona Response Systems, LLC
gunplumber is offline   Reply With Quote
Old December 11, 2017, 17:38   #27
308/223shooter
FALAholic enabler
Gold Contributor
 
308/223shooter's Avatar
 
FALaholic #: 15405
Join Date: Sep 2004
Location: pacific northwest
Posts: 6,190
Has anyone else noticed how foul these smell? Don't know what DSA uses for a preservative, but my FFL says he'll no longer open my packages till I'm there to pick it up. Even in the trunk, it's reaking out my car
__________________
What if the Mystery Babalon described in Revelation, which is destroyed by the nations of the North, is actually America?

The biggest problem with religion is those who claim to know Jesus, then turn around and deny Him with their lifestyle. That is what a unbelieving world, simply finds unbelievable.

Before you die, you should have a will with extra copies. The old saying "No one will screw you faster than family" is bloody well true.
308/223shooter is online now   Reply With Quote
Old December 11, 2017, 19:36   #28
Tgeorgi2002
Curio & Relic
Silver Contributor
 
FALaholic #: 50534
Join Date: Nov 2009
Location: Somewhere...
Posts: 2,564
Quote:
Originally Posted by 308/223shooter View Post
Has anyone else noticed how foul these smell? Don't know what DSA uses for a preservative, but my FFL says he'll no longer open my packages till I'm there to pick it up. Even in the trunk, it's reaking out my car

Covered in bullshit?
Tgeorgi2002 is online now   Reply With Quote
Old December 11, 2017, 19:43   #29
308/223shooter
FALAholic enabler
Gold Contributor
 
308/223shooter's Avatar
 
FALaholic #: 15405
Join Date: Sep 2004
Location: pacific northwest
Posts: 6,190
Well, so far the mag fit passes. Barrel timed fine. Then I found the bolt carrier binds in the rails about a half inch before the chamber. It'll close if I force it, then have to pry it open.
It's fixable, but for what I'm into it with tax and transfer, I could get a Imbel used or otherwais for anuther couple bills and not have to muck about with hand fitting the most expensive part.
I'm not going to return it. I've dealt with that scenario before and don't want the wait and bullsjit.
I'll make this one work, and relegate it to "beater trunk gun".
I've learned my lesson this time, I swear it.
__________________
What if the Mystery Babalon described in Revelation, which is destroyed by the nations of the North, is actually America?

The biggest problem with religion is those who claim to know Jesus, then turn around and deny Him with their lifestyle. That is what a unbelieving world, simply finds unbelievable.

Before you die, you should have a will with extra copies. The old saying "No one will screw you faster than family" is bloody well true.
308/223shooter is online now   Reply With Quote
Old December 11, 2017, 19:52   #30
gunplumber
Arrogant Bastard
Gold Contributor
 
gunplumber's Avatar
 
FALaholic #: 96
Join Date: Jul 2000
Location: Surprise, AZ
Posts: 24,258
Quote:
Originally Posted by 308/223shooter View Post
the bolt carrier binds in the rails about a half inch before the chamber.
Check for a "step" on the front of the rail - a common defect of DSA receivers. Best removed from front before barrel install.

Note - when testing for bolt carrier fit with the bolt, pull the extractor and screw the barrel in to hand tight. Otherwise the bolt can go too far forward and interfere with proper lockup, giving a false "fail" reading (binding).
__________________
T. Mark Graham, Master Gunsmith
Arizona Response Systems, LLC
gunplumber is offline   Reply With Quote
Old December 11, 2017, 21:21   #31
308/223shooter
FALAholic enabler
Gold Contributor
 
308/223shooter's Avatar
 
FALaholic #: 15405
Join Date: Sep 2004
Location: pacific northwest
Posts: 6,190
Yah, got that sorted, except now the bolt group won't come close to closing on a .253. Gauge. To be sure, this is the last DSA receiver I buy that isn't a early forged. Actualy, **** it. I'm sticking with Imbels.
__________________
What if the Mystery Babalon described in Revelation, which is destroyed by the nations of the North, is actually America?

The biggest problem with religion is those who claim to know Jesus, then turn around and deny Him with their lifestyle. That is what a unbelieving world, simply finds unbelievable.

Before you die, you should have a will with extra copies. The old saying "No one will screw you faster than family" is bloody well true.
308/223shooter is online now   Reply With Quote
Old December 12, 2017, 14:16   #32
308/223shooter
FALAholic enabler
Gold Contributor
 
308/223shooter's Avatar
 
FALaholic #: 15405
Join Date: Sep 2004
Location: pacific northwest
Posts: 6,190
This is what sours me on any further DSA receiver purchase. They MUST be aware of the problem, so much so in fact, my guess is the "contract over run" is actually a attempt to recoup investment on defective parts. They can't use these receivers for the contract, which means they must replace them with good receivers. So what to do? Dump them on the market, and hope enough of them are "just good enough" to avoid any warranty backlash.
I like this comment Mark;

"I don't know, because I have to do the build to find the problems. If it's already barreled, then I have to pull the barrel, which is more work than starting with a virgin build. So I don't know that I can do it for less than the cost of a complete build. It would start at the $350 rebuild price.

What has been helpful about doing them in sequence, and writing everything down (instead of just cursing, sputtering, and kicking the wall), is that now I can anticipate problems, rather than discovering them at the testfire range and losing all that work.

I have not yet charged extra for DSA builds, but it looks like I'm either going to have a "Out-of-spec DSA surcharge" or charge everyone more and then offer a discount for IMBELs, LMTs, or other quality in-spec receivers. It is currently costing me over $150 in shop time - above the price of the build - to correct or work around DSA's defects. And that does not count the days of experimenting I did to work out these techniques. I can't continue to eat those expenses.

GF suggested last night, that a pattern of defects across multiple people in multiple states, is a class-action lawsuit waiting to happen. But I don't want DSA sued out of business for their defective crap - I want their defective crap fixed!

And the part that has me so angry and frustrated and disappointed, is I perform all these checks in 5 minutes on a virgin receiver, with a couple factory parts, and a few home-made gauges. Just like I taught Entreprise when they flew out to have me evaluate their last receiver run. I gave them all the different GO/NOGO options for checking a receiver. Nothing fancy, just methodical and disciplined procedures. But they apparently never bothered to use them!

While quality control checks will reveal problems, they don't change The Chicago Way. DSA needs a cultural change, starting with Dave. He has knowingly and willingly shipped defective products for a long time. Nothing is going to change until the man at the top is replaced by someone with integrity. And if the board of directors is unwilling to do that (because they too represent The Chicago Way), there will be no change.

Or someone else needs to come along and make good receivers. But I doubt it would be profitable anymore. But any serious contender can have all the tech support I've collected over the years."
__________________
The $350.00 additional price to deal with correcting defects, providing the receiver isn't too warped, would run the cost up to $650.00 for one of these current parts. One could buy a Imbel or LMT for that price, and not have to deal with the bullshit. This is not worth it in my opinion, nor is the extra amount of time to do the hand work at home, which I wouldn't have to do if the bloody receiver was as advertised, you know "made to original design specifications."
__________________
What if the Mystery Babalon described in Revelation, which is destroyed by the nations of the North, is actually America?

The biggest problem with religion is those who claim to know Jesus, then turn around and deny Him with their lifestyle. That is what a unbelieving world, simply finds unbelievable.

Before you die, you should have a will with extra copies. The old saying "No one will screw you faster than family" is bloody well true.
308/223shooter is online now   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 02:26.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
©1998-2018 The FAL Files