The FAL Files

The FAL Files (http://www.falfiles.com/forums/index.php)
-   The AK Files (http://www.falfiles.com/forums/forumdisplay.php?f=124)
-   -   Info on a new toy (http://www.falfiles.com/forums/showthread.php?t=423981)

1769 February 10, 2018 07:37

Info on a new toy
 
I have come to own an Armory USA, AK. 885-c, I think it is. It shoots pretty good with the iron sights, but the hand guards are loose. So the quad rails would be useless to attach a red dot, which is my hope. The trigger is better than my Rem. 700, once you take up the first stage. I'm kinda liking this thing. I acquired it in my brothers will, along with others.

pre1989 February 12, 2018 13:12

Armory USA is a decent company if I remember ...

You can mount a optic with

1. The side scope rail most AK have ( plenty of mounts out there just put your optic and go from there )
2. A gas tube mount
3. On the rear sight block but eh

All work fine

And you can tighten up the handguns but eh I would not worry about it unless a major issue

I cant rember if the Armory guns had a USA made barrel or not on them

Texgunner February 12, 2018 16:27

A friend has a Global Trades (/Armory USA) SSR-85C, built around 2000?, that is the finest Kalashnikov rifle I've ever seen. They were built on Hungarian FEG receivers with Polish AK-type barrels. They came with beautiful blonde elm furniture iirc. His is just about perfect in fit and finish and very accurate. I later bought one of, if not the last, of this original series of rifles. They later produced several other models of rifles with parts of different origin.

1769 February 14, 2018 03:02

Thanks for the info. My rifle has composite stocks, and the receiver says Bulgaria on it. I need to get out for a serious range day, but the weather has not been cooperating of late. It's either been incredibly cold, or it's snowing, or it warms a bit and rains,, then there's the ice.

gunplumber February 14, 2018 07:38

Armory manufactured receivers are horrible. But if it's an Armory import Bulgarian, I'm sure it's fine. If it is early stamped Bulgarian pattern, it will be an AK, not an AKM, so will lack the leaf-spring tensioner in the lower handguard. You can swap for an AKM lower handguard, or add a shim between the lower handguard and the handguard support. There should be slight tension when rotating the handguard support lever to the rear.

The Ultimak rail is a good way to forward-mount a red dot.

Texgunner February 14, 2018 07:58

Quote:

Originally Posted by gunplumber (Post 4540880)
Armory manufactured receivers are horrible.

The only Kalashnikov that I've ever seen that just would not work was built on an Armory USA receiver. It was an InterArms Tantal that I bought from Blaine Bunting at Atlantic Firearms. They were matching number Polish parts on an Armory receiver. The gun would not fire two consecutive shots. It was returned to Blaine and he shipped it back to Houston, and they replaced it with one built on a Nodak receiver. That rifle runs great.

I always suspected an out of spec receiver on the first rifle. After firing, it extracted and ejected the spent case, loaded another round and then the bolt stopped about 3/4" "out of battery" and had to be driven back with a mallet! Every time. With any magazine tried. I never saw any AK act that way.

gunplumber February 14, 2018 08:51

The location of the hammer, trigger, and selector axle holes is way off. A "shepherds crook" standard axle-retaining plate will not fit. It is primarily the hole for the selector being too low.

My guess from your description, is the incorrect location of the FCG holes prevented the hammer from camming back correctly, locking the hammer and preventing the carrier from passing over it.

1769 February 15, 2018 00:56

Thanks GP. Always with the good information.

pmf February 16, 2018 10:16

My Arsenal SLR-96 is my nicest AK, but the Century SAR-1 goes to the range more because it has a side mounted optic mount that I use a Kalinka sight on. Biggest con of that gun is the serious trigger slap. I put a rubber tube over the trigger which helps a lot.

gunplumber February 16, 2018 12:22

Quote:

Originally Posted by pmf (Post 4541969)
Biggest con of that gun is the serious trigger slap. I put a rubber tube over the trigger which helps a lot.

Why not correct the problem? You have a partial tail on the disconnector - it needs to come off completely. If you still have slap, it's a bad disconnector spring hole depth, bad spring, or the clearance in your receiver is allowing the trigger to pull too far to the rear. 5-10 minutes work.

Timber Wolf February 17, 2018 13:57

Quote:

Originally Posted by pmf (Post 4541969)
My Arsenal SLR-96 is my nicest AK, but the Century SAR-1 goes to the range more because it has a side mounted optic mount that I use a Kalinka sight on. Biggest con of that gun is the serious trigger slap. I put a rubber tube over the trigger which helps a lot.

Funny, both of the SAR-1s as well as 3 SAR-3s I have tried were fine. But two SAR-2s were TERRIBLE. It plum hurt to shoot them. Bobbing the disconnector fixed them both though. Off topic, but the SAR-2s were the best overall gun purchases I have ever made. Bought the rifles when they were cheap (less than $300 NIB). Bought magazines in new sealed four packs with pouch for like $14 and ammo by the case for cheap (and stacked it deep;)). Even got the folding stocks cheap. A man has to accessorize you know.:whistling:

gunplumber February 17, 2018 14:05

While I had done work on the Galils (my first semiauto), it was retrofitting the thumbhole SAR-2s that was my big jump into AK work. Worked with FSE for the compliance parts and IWD for the wood. Only thing I regret was not picking up one of those cheap 5.45 DDR police sniper rifles at the time, as well.


All times are GMT -5. The time now is 05:59.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
©1998-2018 The FAL Files