PDA

View Full Version : Barrels: defective L1A1 Barrels


av8tor
January 26, 2002, 17:59
The Information below is contained in the
L1A1 EMER’s
Technical Handbook - Field Level Repairs
Revision Dated: September, 1985


Barrels Defective

27. Rifles fitted with barrels marked FB 385 of Feb. 1985 manufacturer are to be labeled accordingly and sentenced “Z”

Barrels - Hardness Testing

28. Barrels found to be marked JBS7 but not marked “H” should be tested for hardness in the area 1/2 in. to 4 1/2 in. foreword of the breaching face. Five readings should be taken over the 3 in. and the average reading should fall within the limits 360 +/- 10 VPN or DPN

29. Barrels which pass the test should be marked “H” with a 5/64 in. steel stamps on or near one of the reinforcing flats. Barrels which fail the test are to be sentenced “BR” and the rifle is to be sentenced “Z”

30. Workshops without hardness testing facilities are to make necessary arrangements for testing to be carried out in workshop which has.

***Note: I haven’t stumbled upon the key yet for the various codes, but every indication is that the “Z” means the rifle or part is in need of a critical repair and “BR” indicates the rifle or part is unsafe, cannot be repaired and must be taken out of service. I’ll ad to this post if I come across more barrel information

The Information below is contained in the
L1A1 EMER’s
Technical Handbook - Base Level Repairs
Revision Dated: Jan. 1979

Flaw Detection

14. With the exceptions detailed in para 15, barrels of rifles, including replacement barrels which bear the RSAF test mark as shown in Fig. 4006(b) do not require to be subjected to further flaw detection during overhaul, specified repair or rust proofing.

*** Note: Fig. 4006(A) and Fig 4006(B) shows the RSAF Enfield mark as being a triangle located on one of the barrel flats, with the triangle pointing towards the muzzle end. The REME Base workshop mark appears as a circle with two lines, 180 degrees apart and each extending from the circumference at the center with a specified maximum length of 5/32 in. and a maximum width of 3/32 in.


15. When found barrels of rifles produced at BSA Shirley and RSAF Enfield during 1957-1961 inclusive, must still be flaw detected, using the equipment and techniques referred to in Workshop N 810 para 13. Flaw detection will be carried out even where evidence of previous test by REME or RSAF workshops existed tested barrels as shown in Fig 4006(B). Barrels produced at these locations during this period were manufactured from material which contained seams produced during rolling and this increases the risk of cracks developing in use under service conditions.

16. Barrels produced at BSA Shirley, RSAF Enfield, and ROF Frazackerly may be identified as shown below:

A. BSA Shirley marked BXX 960-2006 on barrel.

B. RSAF Enfield marked 960-2006 on barrel with DXX on reinforce.

C. ROF Frazackerly marked 960-2006 on barrel with FXX on reinforce.

Note: XX indicates year of manufacture ie., 57-61

17. Barrels produced at ROF Frazackerly have not at the present time been the subject of AF G3660 action through split barrels. 100% flaw detection was carried out throughout their production which ceased in 1960. Barrels which carry a flaw detection test mark may be accepted as serviceable without further testing. Barrels of Frazackerly manufacture without an identifiable flaw detection test mark are to be treated as detailed in para 15.

18. Doubtful barrels and those which fail the test are to rendered unserviceable and scrapped.

19. Existing crack test marks, proof marks or batch markings should not be obliterated when applying the mark shown at Fig 4006(B). Should it not be possible to mark on the breaching flat, the mark should be placed on the flange adjacent to the flat.

Proof Markings

20. All barrels must carry a legible proof mark, any rifles found without markings are to be reported to SO1, EME 10c (Chief Quality Engineer), HQ DGEME, Logistic Executive (Army), Andover, Hantis SP11 8HT.

21. Barrels are to be replaced if the gas block is found to be loose, or has moved and also if the wings of the protector foresight are fractured, or distorted beyond repair.


Av
whew if there is any more typo's ya just gotta forgive me LOL, omg I hope someone appreciates this :D

[ January 26, 2002: Message edited by: av8tor ]

[ January 28, 2002: Message edited by: EMDII ]

idsubgun
January 26, 2002, 18:51
Good stuff.
Where can a person find this book? I would like to buy one.

Thanks.

av8tor
January 26, 2002, 19:07
It's not just a book idsubgun, it's a collection of the L1A1 "EMER's"(Command of the Defense Council's Electrical and Mechanical Engineering Regulations)handbooks from the S.A.C.S, School of Infantry in Warminster, :D

Av

[ January 26, 2002: Message edited by: av8tor ]

NZ L1A1 Collector
January 26, 2002, 19:44
The info EMER (Electrical, Mechanical, Engineering Regulations) are British Crown Copyright. These were only issued to units that had Armourers attached to them and basically it is the Bible for Armourers on the L1A1.

For info about the L1A1 & L2A1 you need the Australian EMEI (Electrical, Mechanical, Engineering Instructions).

For the Canadian instructions you need the CAEMEM (Canadian Army Electrical Mechanical Engineering Manual), then later CFTO (Canadian Forces Technical Order).

99% of these instructions have been destroyied as the rifle are now out of service. Here is a list of the main instrutions;


List of Canadian Instructions

CAEMEM, WPN C 819 Instr 9, Iss 1, Dated 16 May 61, RIFLE 7.62 MM, FN, (C1) :~ Miscellaneous Instruction
CAEMEM, WPN C 820, Iss 3, Dated 30 Mar 62, RIFLE, 7.62 MM, FN, (C1) A1 :~ Data Summary
CAEMEM, WPN C 822, Iss 1, Dated 27 Feb 63, RIFLE, 7.62 MM, FN (C1) A1 :~ Descrpition
CAEMEM, WPN C 823 Instr 1, Iss 1, Dated 21 Feb 62, RIFLE, 7.62 MM FN (C1) A1 :~ Unit Repair
CAEMEM, WPN C 825 Instr 1, Iss 2, Dated 24 Jan 62, RIFLE, 7.62 MM FN (C1) A1 :~ Periodic Inspection Standard
CAEMEM, WPN C 829 Instr 1, Iss 1, Dated 20 Feb 62, RIFLE, 7.62 MM FN (C1) A1 :~ Miscellaneous Instruction
CAEMEM, WPN C 829 Instr 12, Iss 1, Dated 22 Oct 71, RIFLE, 7.62 MM, FN, C1A1 :~ Miscellaneous Instruction
CAEMEM, WPN C 829 Instr 2, Iss 1, Dated 14 Feb 62, RIFLE, 7.62 MM FN (C1) A1 :~ Miscellaneous Instruction
CAEMEM, WPN C 829 Instr 4, Iss 1, Dated 19 Jan 63, RIFLE, 7.62 MM FN (C1) A1 :~ Miscellaneous Instruction
CAEMEM, WPN C 829 Instr 5, Iss 1, Dated 14 Apr 65, RIFLE, 7.62 MM FN (C1) A1 :~ Miscellaneous Instruction
CAEMEM, WPN C 829 Instr 8, Iss 1, Dated 14 Jul 66, RIFLE, 7.62 MM, FN, C1A1 :~ Miscellaneous Instruction
CAEMEM, WPN X 107 Instr 8, Iss 2, Dated 6 Jan 61, TOOL, COMBINATION, 7.62 MM, C1A2 :~ Periodic Inspection Standard
CFTO, C-71-113-000/MA-000, Dated 16-08-1982:- Data Summary, RIFLE, 7.62 MM, FN, C1A1 AND C1A1D. 1005-21-111-1994, 1005-21-111-1995, 1005-21-111-1996, 1005-21-111-1997, 1005-21-111-1998
CFTO, C-71-113-000/MB-000, Dated 15-11-1982:- Operating Instructions, RIFLE, 7.62 MM, FN, C1A1. 1005-21-111-1994, 1005-21-111-1995, 1005-21-111-1996, 1005-21-111-1997, 1005-21-111-1998
CFTO, C-71-113-000/MD-000, Dated 15-11-1982:- Equipment Description, RIFLE, 7.62 MM, FN, C1A1 AND C1A1D. 1005-21-111-1994, 1005-21-111-1995, 1005-21-111-1996, 1005-21-111-1997, 1005-21-111-1998
CFTO, C-71-113-000/MM-000, Dated 25-11-1982:- First Line Maintenance Instructions, RIFLE, 7.62 MM, FN, C1A1 AND C1A1D.
CFTO, C-71-113-000/MN-000, Dated 25-11-1982:- Second/Third Line Maintenance Instructions, RIFLE, 7.62 MM, FN, C1A1 AND C1A1D. 1005-21-111-1994, 1005-21-111-1995, 1005-21-111-1996, 1005-21-111-1997, 1005-21-111-1998
CFTO, C-71-113-000/MP-000, Dated 01-04-1986:- Fourth Line Maintenance Instructions, RIFLE, 7.62 mm, FN, C1A1 AND C1A1D. (English) 1005-21-111-1994, 1005-21-111-1995, 1005-21-111-1996, 1005-21-111-1997, 1005-21-111-1998
CFTO, C-71-113-000/MX-000, Dated April 1963:- Parts List and RCEME Scales, RIFLE, 7.62 MILLIMETRE, FN, C1, C1A1, C1D AND C1A1D. (formerly 7610-21-112-3893)
CFTO, C-71-113-000/MY-000, Dated 20-05-1982:- Parts Identification List, RIFLE, 7.62 MM, FN, C1A1 AND C1A1D. 1005-21-111-1996 & 1005-21-111-1998
CFTO, C-71-113-000/NP-000, Iss 1, Dated 25 Aug 67:- Permissive Repair Schedule, RIFLE, 7.62 mm, FN, (C1) A1.
CFTO, C-71-116-000/MA-000, Dated 26-05-1982:- Data Summary, RIFLE, AUTOMATIC 7.62 MILLIMETRE, FN, C2A1 1005-21-111-1999
CFTO, C-71-116-000/MA-000, Dated 29-11-1982:- Operating Instructions, RIFLE, AUTOMATIC 7.62 MM, C2A1 1005-21-111-1999
CFTO, C-71-116-000/MA-000, Dated 30-06-1983:- Equipment Description, RIFLE, AUTOMATIC 7.62 MM, FN, C2A1 1005-21-111-1999
CFTO, C-71-116-000/MA-000, Dated 30-06-1983:- Equipment Description, RIFLE, AUTOMATIC 7.62 MM, FN, C2A1 1005-21-111-1999
CFTO, C-71-116-000/MA-000, Dated 30-06-1983:- First Line Maintenance Instructions, RIFLE, AUTOMATIC 7.62 MM, FN, C2A1 1005-21-111-1999
CFTO, C-71-116-000/MA-000, Weapons E110, Iss 1, Dated 25 Sep 62:- Data Summary, RIFLE, AUTOMATIC 7.62 MILLIMETRE, FN, C2A1 1005-21-111-2005
CFTO, C-71-116-000/MN-000, Weapons E114, Iss 1, Dated 6 Jul 67:- Field and Depot Repairs, RIFLE, AUTOMATIC 7.62 MM, FN, C2A1
CFTO, C-71-116-000/MN-001, Weapons E119 Instr 1, Iss 1, Dated 14 Apr 65:- Miscellaneous Instruction, RIFLE, AUTOMATIC 7.62 MILLIMETRE, FN, C2A1:- Loose or broken ejector block retaining pin.
CFTO, C-71-116-000/MN-002, Weapons E119 Instr 7, Iss 2, Dated 8 Dec 72:- Miscellaneous Instruction, RIFLE, AUTOMATIC 7.62 MILLIMETRE, FN, C2A1:- Band, Bipod Catch.
CFTO, C-71-116-000/MP-000, Dated 01-04-1986:- Fourth Line Maintenance Instructions, RIFLE, AUTOMATIC 7.62 mm, FN, C2A1 (English) 1005-21-111-1999
CFTO, C-71-116-000/MY-000, Dated 20-05-1982:- Parts Identification List, RIFLE, AUTOMATIC 7.62 MM, C2A1. 1005-21-111-1999 & 1005-21-111-2005
CFTO, C-71-116-000/NP-000, Dated 11-12-1986:- Permissive Repair Schedule and Standard Repair Times, RIFLE, AUTOMATIC FN. 7.62 mm, C2A1. 1005-21-111-1999 (English)


List of Australian Instructions

EMEI WPN D250, Iss 3, Apr 81, RIFLE, 7.62 MM, L1A1:~ Data Summary.
EMEI WPN D252, Iss 3, Apr 81, RIFLE, 7.62 MM, L1A1:~ Technical Description.
EMEI WPN D253, Iss 7, Sep 73, RIFLE, 7.62 MM, L1A1 :~ Unit Repair.
EMEI WPN D253-1, Iss 1, Aug 78, RIFLE, 7.62 MM, L1A1, TOP COVER :~ Unit Repair.
EMEI WPN D253-11, Iss 1, Apr 69, RIFLE, 7.62 MM, L1A1, BARREL GROUP :~ Unit Repair.
EMEI WPN D253-12, Iss 1, Feb 84, RIFLE, 7.62 MM, L1A1, TRIGGER MECHANISM HOUSING / BODY LATERAL MOVEMENT REPAIR :~ Unit Repair Introduction.
EMEI WPN D253-13, Iss 1, Jun 83, RIFLE, 7.62 MM L1A1, SIGHT, LOW LIGHT LEVEL, L5A3, FITTING PROCEDURE AND SAFETY PRECAUTIONS :~ Unit Repair Introduction.
EMEI WPN D253-2, Iss 1, 31 Mar 65, RIFLE, 7.62 MM, L1A1, HANDLE, CARRYING ASSEMBLY :~ Unit Repair.
EMEI WPN D253-5, Iss 2, 27 Sep 68, RIFLE, 7.62 MM, L1A1, LOCKING SHOULDERS :~ Unit Repair.
EMEI WPN D254, Iss 6, May 73, RIFLE, 7.62 MM L1A1 :~ Field and Base Repair Introduction.
EMEI WPN D254-1, Iss 4, Feb 84, RIFLE, 7.62 MM, L1A1, BREECHING UP BARRELS :~ Base Repair.
EMEI WPN D254-2, Iss 6, Sep 72, RIFLE, 7.62 MM, L1A1, LOCKING SHOULDERS :~ Field and Base Repair Introduction.
EMEI WPN D254-4, Iss 2, Sep 81, RIFLE 7.62 MM L1A1, REBUILD STANDARDS :~ Base Repair Introduction.
EMEI WPN D257-2, Iss 1, May 70, RIFLE, 7.62 MM, L1A1, CONVERSION TO AUTOMATIC FIRE:~ Modification Instruction.
EMEI WPN D257-3, Iss 1, Oct 72, RIFLE, 7.62 MM, L1A1, BREECH BLOCK ASSEMBLY - EXTRACTOR :~ Modification Instruction.
EMEI WPN D258, Iss 2, Dec 79, RIFLE, 7.62 MM, L1A1, EQUIPMENT INSPECTION AND EXAMINATION DATA :~ Introduction.
EMEI WPN D259, Iss 1, Jun 77, RIFLE 7.62 MM L1A1, CONVERSION OF RIFLE TO DRILL PURPOSE :~ Miscellaneous Instruction.
EMEI WPN D259-1, Iss 1, Aug 77, RIFLE, 7.62 MM, L1A1, FITTING OF TRILUX NIGHTSIGHTS :~ Miscellaneous Instruction.
EMEI WPN D259-2, Iss 1, Nov 80, RIFLE, 7.62 MM, L1A1, SEALING WASHER AND SCREW :~ Miscellaneous Instruction.


List of British Instructions

EMER SA & MG D110, Technical Handbook - DATA SUMMARY
EMER SA & MG D112, RIFLE 7.62 MM L1A1. MAGAZINE 7.62 MM L2A1; LAUNCHER RIFLE GRENADE L1A2; BLANK FIRING ATTACHMENTS L1A2 AND L6A1; ADAPTOR MAGAZINE CHARGING; MOUNT WEAPONSIGHT RIFLE 7.62 MM XL2E2; MOUNT INFRA-RED WEAPONSIGHT 7.62 MM L1A
EMER SA & MG D113, RIFLE 7.62 MM L1A1. MAGAZINE 7.62 MM L2A1; LAUNCHER RIFLE GRENADE L1A2; BLANK FIRING ATTACHMENTS L1A2 AND L6A1; ADAPTOR MAGAZINE CHARGING; MOUNT INFRA-RED WEAPONSIGHT 7.62 MM L1A1; MOUNT WEAPONSIGHT RIFLE 7.62 MM XL2E2
EMER SA & MG D114, Part 1, RIFLE 7.62 MM L1A1. MAGAZINE 7.62 MM L2A1; LAUNCHER RIFLE GRENADE L1A2; BLANK FIRING ATTACHMENTS L1A2 AND L6A1; ADAPTOR MAGAZINE CHARGING; MOUNT INFRA-RED WEAPONSIGHT 7.62 MM L1A1; MOUNT WEAPONSIGHT RIFLE 7.62
EMER SA & MG D114, Part 2, RIFLE 7.62 MM L1A1. MAGAZINE 7.62 MM L2A1; LAUNCHER RIFLE GRENADE L1A2; BLANK FIRING ATTACHMENTS L1A2 AND L6A1; ADAPTOR MAGAZINE CHARGING; MOUNT INFRA-RED WEAPONSIGHT 7.62 MM L1A1; MOUNT WEAPONSIGHT RIFLE 7.62
EMER SA & MG D117 Misc Instr No. 1, Iss 1, Sep 59, RIFLE 7.62 MM L1A1, Technical Handbook - Modification Instruction:~ Magazine platform.
EMER SA & MG D117 Misc Instr No. 10, Iss 1, Jan 73, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction:~ Fitting sling attachments for Arctic role.
EMER SA & MG D117 Misc Instr No. 3, Iss 2, Feb 61, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction:~ Numbering of breech block and carrier.
EMER SA & MG D117 Misc Instr No. 5, Iss 2, 17 May 65, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction:~ Fitting of new design carrying handle retaining screw.
EMER SA & MG D117 Misc Instr No. 6, Iss 1, 20 Aug 62, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction:~ Fitting of new type ring, retaining, grenade.
EMER SA & MG D117 Misc Instr No. 8, Iss 1, 15 Mar 63, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction:~ Chamfering of cocking handle components.
EMER SA & MG D117 Misc Instr No. 9, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction:~ Adaptor magazine charging - radius added to frame.
EMER SA & MG D118, RIFLE 7.62 MM L1A1. MAGAZINE 7.62 MM L2A1; LAUNCHER RIFLE GRENADE L1A2; BLANK FIRING ATTACHMENTS L1A2 AND L6A1; ADAPTOR MAGAZINE CHARGING; MOUNT INFRA-RED WEAPONSIGHT 7.62 MM L1A1; MOUNT WEAPONSIGHT RIFLE 7.62 MM XL2E2
EMER SA & MG D119, Misc Instr No. 10, Iss 1, 12 Jun 69, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Handguards - Alternative repair method.
EMER SA & MG D119, Misc Instr No. 16, Iss 4, May 76, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Nylon plastic furniture.
EMER SA & MG D119, Misc Instr No. 19, Iss 1, Mar 73, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Conversion of rifle for use on CIM's and gunnery training turrets.
EMER SA & MG D119, Misc Instr No. 22, Iss 1, Apr 74, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Leaf, backsight, B1/1005-99-960-2507 and B1/1005-99-960-2508 misalignment of axis pin holes.
EMER SA & MG D119, Misc Instr No. 28, Iss 1, Jan 75, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Flash Eliminator (B1/1005-99-963-3422) incorrectly machined.
EMER SA & MG D119, Misc Instr No. 29, Iss 1, Aug 75, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Gauging of firing pin protrusion.
EMER SA & MG D119, Misc Instr No. 30, Iss 1, Dec 75, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Introduction into service of barrels with Chordal rifling.
EMER SA & MG D119, Misc Instr No. 31, Iss 1, Apr 76, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Fitting of But Small Arms (B1/1005-99-965-1966.
EMER SA & MG D119, Misc Instr No. 33, Iss 1, May 77, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Repair technique -handguards.
EMER SA & MG D119, Misc Instr No. 36, Iss 1, Aug 78, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Plug Butt Plate (B1/1005-99-963-2040).
EMER SA & MG D119, Misc Instr No. 38, Iss 1, Aug 81, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Fractured breech blocks.
EMER SA & MG D119, Misc Instr No. 6, Iss 1, 31 Dec 64, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Jamming of Gas Plugs.
EMER SA & MG D119, Misc Instr No. 7, Iss 1, 17 Apr 68, RIFLE 7.62 MM L1A1, Technical Handbook - Miscellaneous Instruction: Chamfer added to leaf, backsight, front.

dino1
January 26, 2002, 21:14
Kevin, I hope you didn't type all that out for us! major case of TMI!

[ January 26, 2002: Message edited by: dino1 ]

av8tor
January 26, 2002, 21:22
omg Kevin, it would have took me 3 days to type that LOL :D
But yep, thats them...does that mean we got the other 1% ;)

Av

[ January 26, 2002: Message edited by: av8tor ]

NZ L1A1 Collector
January 26, 2002, 21:35
yessssssssssss just for you guys I worked my fingers to the bone and now my RSI is playing up ;)

I had already had that list typed and stored away, All I had to do was retrive it and reformat it for this medium. I have been working on computerizing the latest information of the British (EMER) in the hope of producing a booklet of the info. A very long job, expecially trying to catch all the formating, gramatical problems and pics.

I'm always looking for new segments and Issues of the instructions, Av8tor would you be able to send me a list of the instructions you have... titles/Issue/date's?

[ January 26, 2002: Message edited by: NZ L1A1 Collector ]

av8tor
January 26, 2002, 21:39
Sure, but I only type about 3 words a minute, and 2 of them will be spelled wrong LOL,

seriously, sure Kevin, maybe we can fill any gaps in the others set.

Give me a couple/three days ok, Im way behind on a proposal Im trying to get together for work.

Now, on the trail for a set of the izzy version :)

Do you want me to send it to your posted email addy when I get the list made?
Is the list you posted the ones you already have? and do you want me to just email ya the ones that isnt on your list?

Av

[ January 26, 2002: Message edited by: av8tor ]

[ January 26, 2002: Message edited by: av8tor ]

NZ L1A1 Collector
January 26, 2002, 22:07
Might as well make it as easy fo you as possable ;)

Just list what's not shown, including different issues. List them like this for ease
eg.
D113, Iss 3, dated 24 Jan 68
D114 Pt 1, Iss 7, dated 11 Sep 70
D114 Pt 1, Iss 10, dated 20 Nov 82

etc. That will be the easiest way of doing it and won't require too much typing :D

Could you send it to my lised email address please.

I hope you know Hebrew if you want the Izzy stuff!

av8tor
January 26, 2002, 22:22
Sounds good Kevin, I'll need to log them all anyways to know what I'm missing if anything, Soooo much information, My goodness there is information on everything from field mods for artic use to rechroming gas pistons.

Mine just arrived a couple days ago, so Ive only scratched the surface, I dont know what Ive got yet, but after reading only 3 pages I went and posted the info about locking shoulders in Gunsmith and BIY, figured I would post any safety related issues I came across. Great info, wonderful resource.

Try to get it to ya by Thursday, ;)

Av

av8tor
February 03, 2002, 12:22
Hi Kevin,

Finally getting started on the list and omg I didn’t realize, So far the newest document I’ve come across is 1991, if this set isn’t the last revision it has to be close to it :)

1 Rifle 7.62 MM L1A1, Magazine 7.62 MM L2A1, Blank Firing Attachments L1A2 and L6A1 Mount Weaponsight Rifle 7.62 MM L2A1
Technical Handbook - Unit Repairs
D113 issue 13 Rev. Jan. 1984

2. Rifle 7.62 MM L1A1, Magazine 7.62 MM L2A1, Mount Weaponsight Rifle 7.62 MM XL2E2 Technical Handbook - Field Repairs
D114 part 1 and 2 Rev. Jan. 1985

3. Magazine 7.62 MM L2A1; Launcher Rifle Grenade L1A2; Blank Firing Attachments L1A2 and L6A1; Adaptor Magazine Charging; Mount Weaponsight Rifle 7.62 MM XL2E2; Mount Infrared Weaponsight 7.62 MM L1A1
Technical Handbook - Data Summary
D110 issue 2 Rev. Jan. 1975

4. Magazine 7.62 MM L2A1; Launcher Rifle Grenade L1A2; Blank Firing Attachments L1A2 and L6A1; Adaptor Magazine Charging; Mount Infrared Weaponsight 7.62 MM L1A1; Mount Weaponsight Rifle 7.62 MM L2A1 and L2A2
Technical Handbook - Unit, Field and Base Inspection Standards
D118 Rev. Dec. 1981

5. Rifle 7.62 MM L1A1
Technical Handbook - Miscellaneous Instruction Index
(Contains separate documents on repairs/mods/regulations, Ill come back to this and list them individually, asap)
D119 Rev. Sept. 1991

6. Magazine 7.62 MM L2A1; Launcher Rifle Grenade L1A2; Blank Firing Attachments L1A2 and L6A1; Adaptor Magazine Charging; Mount Weaponsight Rifle 7.62 MM XL2E2; Mount Infrared Weaponsight 7.62 MM L1A1
Technical Handbook - Technical Description
D112 Rev. Jan. 1975


7. Rifle 7.62 MM L1A1
Technical Handbook - Modification Instuctions
(Collection of 12 documents concerning repairs/mods/regulations, again I will itemize them asap)
D117 (Cannot find a date on the last revision, however, the header used in item #12 is unique to other documents which are dated 1991)


HTH :)
Av

[ February 03, 2002: Message edited by: av8tor ]